Hitachi HDPJ52 user manual Option menu, Long max min.  Short min min, Reset  Cancel

Page 53

Advanced Menu (OPTION menu)

OPTION menu

The following functions are accessible via the OPTION menu. After selecting an item according to the procedure described in the preceding "Advanced Menu operation" section (35), refer to the following table for details on operating the selected item.

 MENU [COMPUTER]

   :SELECT

 

 PICTURE

 AUTO OFF      0 min

 

 IMAGE

 LAMP TIME     0 h

ENGLISH

 INPUT

 FILTER TIME   0 h

 SETUP

 SERVICE

 

 SCREEN

 

 

 OPTION

 

 

 EASY MENU

 

 

 

Item

Description

 

Using the ▲/▼ cursor buttons adjusts the amount of time after

 

which the projector off is automatically turned off.

 

 

Long (max. 99 min.) Short (min. 0 min.)

 

 

AUTO OFF

AUTO OFF

 

 

 

 

AUTO OFF

ENABLE

DISABLE

 

10 min

0 min

 

 

If no signal or an unsuitable signal is detected for the time set on

 

this menu, the projector lamp will turn off and the power indicator will

 

blink orange.

 

 

 

Please see “Turning the power off” (23) to complete the process.

 

LAMP TIME is displayed in the OPTION menu as a reference value

 

of the usage time of the lamp. The time displayed is the total time

 

the lamp has been used since the LAMP TIME was last reset.

 

Only reset the LAMP TIME item when you have replaced the lamp

LAMP TIME

so that the LAMP TIME remains accurate.

 

Pressing the ▲ cursor button in the LAMP TIME menu

LAMP TIME

0h

 

resets the LAMP TIME.

 

RESET

 

 

CANCEL

 

RESET CANCEL

 

 

 

 

 

- NOTE -

 

 

 

• Please see “Lamp” (57) for information on lamp replacement.

 

FILTER TIME is displayed in the OPTION menu as a reference

 

value of the usage time of the air filter. The time displayed is the

 

total time the filter has been used since the FILTER TIME was last

 

reset.

 

 

 

Only reset the FILTER TIME item when you have cleaned or

 

replaced the air filter so that the FILTER TIME remains accurate.

 

Pressing the ▲ cursor button in the FILTER TIME menu

FILTER TIME

 

resets the FILTER TIME.

 

FILTER TIME

 

0h

RESET CANCEL

 

RESET

 

CANCEL

 

 

 

 

 

 

- NOTE -

 

 

Please see “Air filter” (58) for information on cleaning and replacing the air filter.

The FILTER MESSAGE that prompts you to clean the air filter “REMINDER…” is displayed based on the FILTER TIME value. Please reset the FILTER TIME when the filter is cleaned or changed so that the message displays correctly.

(Continued on next page)

53

Image 53
Contents Trademark acknowledgment Thank you for purchasing this projectorPreparations Before useProjection Basic operationTroubleshooting MaintenanceWarranty and after-service Specifications Advanced MenuAbout this manual Projector featuresAbout contents of package Projector Part namesComponent Video Control buttonsPorts PC, HDMI, Compo Remote controlCONTRAST, Bright Strap hole Rivet Fastening the lens coverStrap On a horizontal surface Suspended from the ceiling ArrangementFor 43 screens For 169 screensAdjusting the projector’s elevation With a VCR/DVD player Connecting your devicesFor an Scart RGB input For an Hdmi signal sourceFor a DVI signal source Optional Use With a computerAbout Plug-and-Play capability Computer signal examplesVesa Text VesaUsing the cable cover Connecting the power supplyLoading batteries into the remote control Using the remote control button lights Using the remote controlRemote control Sensor Approximately Light buttonPower button Turning the power onPower indicator STANDBY/ON buttonAutomatically adjusting the picture Selecting an input signalAdjusting the zoom Adjusting the display positionAdjusting the focus Zoom ringTurning the power off 169  For no signal or an unrecognized signal 169 fixedWide MOVIE1 MOVIE2Dark BrightTemp Mode Gamma Color IrisNormal Standard Cinema LOWTurn OFF Bright DarkAUTO1 AUTO2MY Memory To load saved adjustment settings MY MEMORY To save adjustment settingsTo switch from the Advanced Menu to the Easy Menu To display a menu when no menu is currently displayedEasy Menu operation To change the display languageEasy Menu functions To reset the operationTo operate the selected item To close the menu Cinema LOW  Normal Cinema High  MusicWeaker  Stronger Darker  BrighterReddish  Greenish MirrorEnglish  Français  Deutsch  Español ResetItaliano  Norsk  Nederlands  Português Language Svenska  Русский  Suomi  Polski  TürkçeAdvanced Menu operation To switch from the Easy Menu to the Advanced MenuTo select a menu To reset the menu settings Standard Picture menu High  CUSTOM-1, CUSTOM-2, CUSTOM-3, CUSTOM-4Step Ramp Gray scale Description To adjust a Custom mode6500K  7500K  9300K  Hi-BRIGHT These modes set the same color temperature as the mode nameCUSTOM-1  CUSTOM-2  CUSTOM-3  CUSTOM-4  6500K, 7500K, 9300KGreenish  Reddish Step  Ramp Gray scaleIris Memory Description To save adjustment settingsOver Scan Using the / cursors buttons changes the aspect ratioImage menu  For a signal from the Hdmi port  For a signal from the Computer port For a signal from the Component Video ports  For a signal from the S-VIDEO or Video portTV  Film  Turn OFF Input menu Film  Auto Component Component  Scart RGB Scart RGB  NTSC, PAL, SECAM, NTSC4.43, M-PAL, N-PALExample for an Hdmi signal Example for computer RGB signalsExample for a video, s-video and component video signal Example for a Scart RGB signalReduce top of the image  Reduce bottom of the image Setup menuKeystone Normal  WhisperMenu Position Screen menuLanguage  MyScreen MyScreen  Original  Turn OFFStart UP  OriginalMessage To move the black bars up and down Using the / cursor buttons switches between the dialogsLong max min.  Short min min Reset  CancelOption menu Using the / cursor buttons changes the rotation FAN Speed  Ghost  Stripe Factory Reset  Filter MessageHigh  Normal Ghost50h  100h  200h  300h  Turn OFF Factory ResetFilter Message Lamp Bottom Projector Lamp cover Screw Replacing the lamp by yourselfAir filter Knobs Air filterFilter Maintenance Lens Cabinet and Remote controlInside of the projector Horizontal or vertical wavelength of the input signal There is no input signalInternal temperature is high Related messagesPower Lamp Temp Regarding the indicator lampsIt is time to clean the air filter Indicator Cooling fan is not operatingThere is a possibility that the interior of the projector Has overheatedBy a power outage blackout, etc Main power source has been interrupted during operationSignal cables are not correctly connected Lens cover is closedMenu function or the remote control Brightness is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableWhisper function is working Set the Whisper item 48 in the Setup menu to NormalWhisper function may cause screen flicker Fan speed has been automatically changedRGB input port SpecificationDigital input port Communication portUnit mm Dimension diagramInterface which is an interface standard for Entry Explanation40, 43, 44 NtscSecam PALScart