Hitachi HDPJ52 user manual Turning the power off, STANDBY/ON button

Page 23

Turning the power off

STANDBY/ON

POWER TEMP LAMP

MENU ENTER

INPUT RESET

Projection

	POWER	LIGHT	ENGLISH
STANDBY/ON button	ASPECT	IRIS	ENGLISH
	BLACK MODE	MEMORY
POWER button	ENTER
POWER button	BRIGHT CONTRAST COLOR
	MENU	RESET

HDMI PC AUTO

COMPO S-VIDEO VIDEO

POWER indicator

1. Press the STANDBY/ON button on the projector or the POWER button on the remote control.

The message "Power off?" will appear on the screen for approximately 5 seconds.

2. Press the STANDBY/ON button on the projector or the POWER button on the remote control again when the “Power off?” message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange.

Then the POWER indicator will stop blinking and light steady orange when the lamp is ﬁnished cooling down.

POWER off ?

POWER （Blinking in orange）

POWER （Steady orange） POWER （Steady orange）

3. Make sure that the power indicator is lit a steady orange, and set the power switch to the OFF position.

The POWER indicator will go off.

Do not set the power switch to the OFF position while the POWER indicator is green or blinking.

4. Close the lens cover. For safety purposes, disconnect the power cord if the projector is not to be used for prolonged periods of time.

NOTE • Turn the power off in right order. Turn off the connected devices ﬁrst and the projector last.

•Except for emergencies, whenever you turn the projector off be sure to follow the procedure explained in “Turning off the power”, and do not disconnect the power cord until the procedure is complete. Neglect can cause damage to the electrode and/or prevent the lamp from lighting.

•This projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly even when turning off the power. If this occurs, please push the restart switch (7, 64) using a pin or similar object. Make sure that the power indicator is lit a steady orange, and set the power switch to the OFF position. Only use the restart switch in exceptional circumstances.

•If there is a power failure, or the restart switch is used, allow the projector to cool down for at least 10 minutes before turning on again.

23

Image 23

Contents Trademark acknowledgment Thank you for purchasing this projectorBasic operation Before usePreparations ProjectionAdvanced Menu MaintenanceTroubleshooting Warranty and after-service SpeciﬁcationsAbout this manual Projector featuresAbout contents of package Projector Part namesComponent Video Control buttonsPorts PC, HDMI, Compo Remote controlCONTRAST, Bright Strap hole Rivet Fastening the lens coverStrap On a horizontal surface Suspended from the ceiling ArrangementFor 43 screens For 169 screensAdjusting the projector’s elevation With a VCR/DVD player Connecting your devicesFor an Scart RGB input For an Hdmi signal sourceFor a DVI signal source Optional Use With a computerVesa Computer signal examplesAbout Plug-and-Play capability Vesa TextUsing the cable cover Connecting the power supplyLoading batteries into the remote control Light button Using the remote controlUsing the remote control button lights Remote control Sensor ApproximatelySTANDBY/ON button Turning the power onPower button Power indicatorAutomatically adjusting the picture Selecting an input signalZoom ring Adjusting the display positionAdjusting the zoom Adjusting the focusTurning the power off MOVIE1 MOVIE2  For no signal or an unrecognized signal 169 ﬁxed169 WideDark BrightCinema LOW Mode Gamma Color IrisTemp Normal StandardAUTO2 Bright DarkTurn OFF AUTO1MY Memory To load saved adjustment settings MY MEMORY To save adjustment settingsTo change the display language To display a menu when no menu is currently displayedTo switch from the Advanced Menu to the Easy Menu Easy Menu operationTo close the menu To reset the operationEasy Menu functions To operate the selected item Music  Normal Cinema LOW  Cinema HighMirror Darker  BrighterWeaker  Stronger Reddish  GreenishLanguage Svenska  Русский  Suomi  Polski  Türkçe ResetEnglish  Français  Deutsch  Español Italiano  Norsk  Nederlands  PortuguêsAdvanced Menu operation To switch from the Easy Menu to the Advanced MenuTo select a menu To reset the menu settings CUSTOM-1, CUSTOM-2, CUSTOM-3, CUSTOM-4 Picture menu Standard  HighStep Ramp Gray scale Description To adjust a Custom mode 6500K, 7500K, 9300K These modes set the same color temperature as the mode name6500K  7500K  9300K  Hi-BRIGHT CUSTOM-1  CUSTOM-2  CUSTOM-3  CUSTOM-4Greenish  Reddish Step  Ramp Gray scaleIris Memory Description To save adjustment settingsOver Scan Using the / cursors buttons changes the aspect ratioImage menu  For a signal from the S-VIDEO or Video port  For a signal from the Computer port For a signal from the Hdmi port  For a signal from the Component Video ports Auto Input menuTV  Film  Turn OFF  Film NTSC, PAL, SECAM, NTSC4.43, M-PAL, N-PAL Component  Scart RGB Component  Scart RGBExample for a Scart RGB signal Example for computer RGB signalsExample for an Hdmi signal Example for a video, s-video and component video signalNormal  Whisper Setup menuReduce top of the image  Reduce bottom of the image KeystoneMenu Position Screen menuLanguage  Original MyScreen  Original  Turn OFF MyScreen Start UPMessage To move the black bars up and down Using the / cursor buttons switches between the dialogsLong max min.  Short min min Reset  CancelOption menu Ghost FAN Speed  Ghost  Stripe Factory Reset  Filter MessageUsing the / cursor buttons changes the rotation High  Normal50h  100h  200h  300h  Turn OFF Factory ResetFilter Message Lamp Bottom Projector Lamp cover Screw Replacing the lamp by yourselfAir ﬁlter Knobs Air ﬁlterFilter Maintenance Lens Cabinet and Remote controlInside of the projector Related messages There is no input signalHorizontal or vertical wavelength of the input signal Internal temperature is highPower Lamp Temp Regarding the indicator lampsHas overheated Indicator Cooling fan is not operatingIt is time to clean the air ﬁlter There is a possibility that the interior of the projectorLens cover is closed Main power source has been interrupted during operationBy a power outage blackout, etc Signal cables are not correctly connectedColor Space setting is not suitable Brightness is adjusted to an extremely low levelMenu function or the remote control Color settings are not correctly adjustedFan speed has been automatically changed Set the Whisper item 48 in the Setup menu to NormalWhisper function is working Whisper function may cause screen ﬂickerCommunication port SpeciﬁcationRGB input port Digital input portUnit mm Dimension diagramNtsc Entry ExplanationInterface which is an interface standard for 40, 43, 44Secam PALScart