Remote Control Functions
Channel Control | 1. Press the Input Selector dij | 2. Press the Input Selector dijl– | |||||||||
The remote may be programmed to operate so | o for the device you wish to program into | ||||||||||
that the channel control function for either the | to have the transport control associated and | the reassigned button. |
| ||||||||
TV, cable or satellite receiver used in your system | the Mute Button c at the same time until | 3. Enter the | |||||||||
may be used in conjunction with one of the other | the red light appears under the Input | ||||||||||
devices controlled by the remote. For example, | Selector | model you wish the reassigned button to | |||||||||
while using and controlling the VCR, you may | Program Indicator LED lights. | operate, and the Program Indicator LED | |||||||||
wish to change channels on a cable box or satel- | 2. Press the Play Button | . The Input | will flash. |
| |||||||
lite receiver without having to change the device | 4. Press the same Input Selector dij | ||||||||||
selected by the DCR600II or the remote. To pro- | Selector | ||||||||||
gram the remote for Channel Control Punch- | once. |
|
|
| |||||||
Through, follow these steps: |
|
|
|
|
|
| store the selection. The red LED under the | ||||
|
| 3. Press and release the Input Selector Button | reassigned Input Selector will flash three | ||||||||
|
|
|
| ||||||||
1. Press the Input | Selector Button dij | times and then go out. |
| ||||||||
the transport (e.g., VCR). The Program | Example: To use the VID2 button to operate | ||||||||||
to have the channel control associated and the | Indicator LED will go out and the Input | ||||||||||
Mute Button c at the same time until the | Selector | a cable box, first press the VID2 Input | |||||||||
red light appears under the Input Selector | in Step 1 will blink three times and then go | Selector m and the Mute Button c at | |||||||||
dijl | out to confirm the data entry. | the same time until the red light glows under | |||||||||
Indicator LED | lights. |
|
|
|
|
|
| the VID2 Button m. Press the CBL/SAT | |||
|
| Example: To control the transport of a DVD | Button n, followed by the | ||||||||
|
|
|
| ||||||||
2. Press the Volume Down Button w. The | player while the remote is set to control the | for the specific model you wish to control. | |||||||||
Program Indicator LED will flash once. | TV, first press the TV Input Selector Button | Finally, press the VID2 Button m again. | |||||||||
3. Press and release the Input Selector Button | o and the Mute Button c at the same |
| Resetting the Remote Memory | ||||||||
time. Next, release them and press the Play |
| ||||||||||
As you add components to your home theater | |||||||||||
Button | , followed by the DVD Input | ||||||||||
be used to change the channels. The Program | Selector Button d. |
|
| system, occasionally you may wish to totally | |||||||
Indicator LED will go out and the Input | NOTE: To remove the Channel Control Punch- | reprogram the remote control without the confu- | |||||||||
Selector | sion of any commands, macros or ”Punch- | ||||||||||
in Step 1 will blink three times and then go | Through and return the remote to its original con- | Through“ programming that you may have done. | |||||||||
out to confirm the data entry. |
|
| figuration, repeat the steps shown in the example | To do this, it is possible to reset the remote to | |||||||
Example: To control the channels using your | above. However, press the same Input Selector | the original factory defaults and command codes | |||||||||
by following these steps. Note, however, that | |||||||||||
cable box or satellite receiver while the | NOTE: Before programming the remote for | once the remote is reset, all commands or codes | |||||||||
remote is set to control the VCR, first press the | that you have entered will be erased and will | ||||||||||
VID 1/VCR 1 Input Selector Button l and | Volume, Channel or Transport | need to be reentered: |
| ||||||||
the Mute Button c at the same time. Next, | make certain that any programming needed to | 1. Press any of the Input Selector Buttons d | |||||||||
release them and press the Volume Down | assign the remote to control the specific TV, CD, | ||||||||||
Button w, followed by the VID 3/CATV/ | DVD, cable or satellite receivers has been | ||||||||||
SAT Input Selector Button n. |
| completed. |
|
|
| at the same time until the Program Indicator | |||||
NOTE: To remove the Channel Control Punch- |
| Reassigning Devices | LED lights. |
| |||||||
|
|
|
| ||||||||
Through and return the remote to its original con- | Although each Input Selector dij | 2. Press the ”3“ Button | three times. | ||||||||
figuration, repeat the steps shown in the exam- |
| 3. The red LED under the Input Selector d | |||||||||
ple above. However, press the same Input | product shown on the remote, it is possible to | ||||||||||
Selector | reassign one of these buttons to operate a sec- | ||||||||||
|
|
|
| ond device of another type. For example, if you |
| press. The Program Indicator LED will flash | |||||
Transport Control | have a cable box and satellite receiver, but only |
| three times and go out. |
| |||||||
The remote may be programmed to operate so | one VCR, you may program the “VID2” button to |
| 4. When the Program Indicator LED goes out, | ||||||||
that the Transport Control | – | functions | operate a cable box. Before following the normal |
| |||||||
| the remote has been reset to the factory settings. | ||||||||||
(Play, Stop, Fast Forward, Rewind, Pause and | programming steps for either |
| |||||||||
|
|
|
| ||||||||
Record) for a VCR, DVD or CD will operate in con- | Auto Search code entry, you must first reassign |
|
|
| |||||||
junction with one of the other devices controlled | the button with the following steps: |
|
|
| |||||||
by the remote. For example, while using and con- | 1. Press the Input Selector dij |
|
|
| |||||||
trolling the TV, you may wish to start or stop your |
|
|
| ||||||||
VCR or DVD without having to change the device |
|
|
| ||||||||
selected by the DCR600II or the remote. To | Button c at the same time until the red |
|
|
| |||||||
program the remote for Transport Control Punch- | light appears under the Input Selector |
|
|
| |||||||
Through, follow these steps: |
|
|
|
|
| ||||||
|
|
|
| Indicator LED lights. |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| 45 |