JBL SCS135P, DVD600II Setting the Linear PCM Bit Rate, Main Input Selector h, the Night Button

Configuring the DVD600II DVD Changer

• On: Select this option to turn on the

Although the DVD600II will play all of these disc

formats are available is limited by the type

Dynamic Range compression circuitry so

types, this setting creates a default that tells

of material recorded on the disc when it was

that the dialogue will remain clear even at

which way to present the soundtracks when

authored.

low volume levels.

there is a choice.

When you have made your selection using the

To select a Digital Audio Output default, you

⁄/ ¤ Buttons y

to highlight the desired

must be viewing the Setup Menu (Figure 1),

option, press the Enter Button

and note

which is available by pressing the Menu

that the circle next to your choice will fill in. The

Button z while the unit is in the Stop mode.

menu system will then automatically return to

At the Setup Menu, press the ¤ Button

the status listing.

until the Digital Audio Out option is highlighted.

If you have no other changes to make after set-

Next, press the Enter Button

. Select

one of the three choices in the options box

ting this default, press the Menu Button z

(Figure 15) using the ⁄/ ¤ Buttons y

.

to remove the Setup Menu from the screen, or

Figure 14

The choices are as follows:

press the Play/Pause Button

to

begin or resume playback.

When you have made your selection using the

• PCM: Choose this setting if most of your

Setting the Linear PCM Bit Rate

⁄/ ¤ Buttons y

to highlight the desired

library consists of conventional CDs.

If the DVD600II detects a high-resolution, 96kHz

option, press the

Enter Button

and note

• Dolby Digital: Choose this setting only if you

audio signal encoded on a disc, it can either

that the

circle next

to your choice will fill in. The

do not plan on listening to any DTS selections.

pass the signal through to the receiver or, if the

menu system will

then automatically return to

Should you choose to watch a DVD movie or

receiver is not capable of processing a 96kHz bit

the status listing.

listen to a CD which has a DTS audio track,

rate signal, the DVD600II can downsample the

If you have no other changes to make after set-

you must return to this menu and change this

signal to 48kHz. The Linear PCM menu enables

selection to DTS.

you to configure the DVD600II to match your

ting this default, press the Menu Button z

receiver by selecting which bit rate the

to remove the Setup Menu from the screen, or

• DTS: We recommend that you choose this

DVD600II should apply.

press the Play/Pause Button

to

setting, since the DCR600II receiver included

begin or resume playback.

with your system is capable of automatically

The bit rate is set at the factory to default to

Note that the performance of the Dynamic

detecting and decoding any of the three

passing the full 96kHz signal through, as the

formats of DTS, Dolby Digital and PCM.

DCR600II receiver is capable of processing this

Range function is dependent on the audio

signal. Therefore, you should not adjust this fea-

format of the disc being played, and whether

ture unless you use the DVD600II with another

or not the disc’s soundtrack is capable of this

receiver that is not capable of processing a

feature.

96kHz signal.

Note that you can achieve the same effect by

using the DCR600II’s Night mode. Simply press

the Main Input Selector h, the Night

Button

, then the ⁄/ ¤ Buttons y

to scroll through the dynamic range choices.

Press the Set Button

to enter the selec-

Figure 15

tion. If you choose to use the Dynamic

Range/Night Mode feature, select it using

NOTE: If you select the DTS option, your

either the DVD600II or the DCR600II, but not

receiver or processor MUST be capable of

both simultaneously.

decoding DTS audio. If the DTS option is chosen

Using the Digital Audio Output

Figure 16

and the unit is connected to a product that can-

DVD players accommodate a variety of audio

not support DTS, no audio will be heard when a

formats, including Dolby Digital, DTS and the

DTS disc is played.

PCM audio format used by conventional CD

Remember, regardless of the option chosen, you

discs and some DVD playback. The DCR600II

receiver can automatically detect any of these

may still have to adjust the settings on your

digital formats. Depending on the format of the

DVD disc or audio equipment, if you do not use

discs in your library, you need to set a default

the DCR600II, to match the output of the

for the type of audio outputs accommodated.

DVD600II. In addition, the choice of which audio

51