Kyocera FS-1010 Errors Requiring Service Personnel Attention, Scanner motor error 4000 error

Page 32

Indicators

3.3.2Errors Requiring Service Personnel Attention

When the following errors occur, turn off your printer, remove the plug from the AC outlet, and contact your Kyocera Mita dealer. The indicators are shown in two different states, according to the way they alternate.

			Indicator		KM-NET for Clients display	Corrective Action
					(None)	Main motor error (“2000”error)
						Contact your Kyocera Mita dealer.

(None)

Scanner motor error (“4000” error)

Contact your Kyocera Mita dealer.

(None)

Scanner pin-photo error (“4200” error)

Contact your Kyocera Mita dealer.

(None)

Eraser error (“5300” error)

Contact your Kyocera Mita dealer.

(Continued on next page)

3-8

Image 32

Contents Printer Regarding Tradenames Limited Warranty LicenseLimitation of Remedies GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Paper Selection FontsAppendix a Options Appendix B Host Computer InterfaceIndex-1 Appendix C Printer SpecificationsGlossary-1 Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Indicators KeysReference Name Status Meaning Reference Name FunctionStatus Installation Options Error LogSoftware Version Hardware InformationKIR Test Pattern Toner GaugeInterface Information Maintenance Toner Kit to be Used Toner Container ReplacementToner Container Replacement Interval Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Cleaning Printer InteriorNever stand the process unit on end Slots in the printer Troubleshooting Symptom Check Items Corrective Action General GuidePrint Quality Problems Clean the charger wirePrinted Results Corrective Action Contact your Kyocera Mita dealerCheck the EcoPrint setting Confirm Toner indicatorTry setting the thin paper mode Check the paper size settingIndicators Maintenance Messages Theprintjobcannotbedoneatcurrentresolution There is no cassette in the feeder, orCassette is not inserted properly After reinserting the paper cassette, you should beErrors Requiring Service Personnel Attention Scanner motor error 4000 errorScanner pin-photo error 4200 error Eraser error 5300 errorError None Waste toner reservoir is full ErrorController RAM read/write error F020 error Waste toner reservoir is fullCommunication error F040 error Engine ROM check sum error F050 errorError Messages Printer power is on Make sure to turn the printer power off before insertingThis message appears when the printer is in the ready Printer has halted because you attempted to insertNormal Indicator Display Indicator KM-NET for Clients display DescriptionCorrecting a Paper Jam Jam at the Face-down and Face-up TraysJam at the Paper Cassette Jam Inside the PrinterInto the printer Paper Selection Paper Specifications SpecificationsSpecification General GuidelinesComposition Selecting the Right PaperCondition of the Paper Basis Weight Paper SizePaper Sizes for Paper Feeding SmoothnessPaper Grain Moisture ContentThickness Caliper Other Paper Properties Transparency overhead projection film Transparency SpecificationsSpecial Paper Adhesive-Backed Labels Adhesive-backed labelAdhesive Label Specifications EnvelopesColored Paper Preprinted PaperRecycled Paper Paper Type Paper Source MP Tray Paper Weight Paper Type CassettePaper Type Fonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Memory CompactFlash CardExpansion Memory Installation YESInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Testing the Expansion Memory To remove a DimmSetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Parallel Interface Communication Modes Interface SignalsParallel Interface Table B.1 Parallel Connector Pin Assignment Pin In/out DescriptionData 0 1 to Data 7 8 Pins 2 to Paper Empty PError PinReset nInit Pin Error* nFault PinPower Ready Pin Select In nSelectIn PinSpecifications USB InterfaceSerial Interface Option 1 RS-232C InterfaceSG Signal Ground Pin Table B.4 RS-422A Signal Pin Assignments2 RS-422A Interface DTR Data Terminal Ready PinOverview of Signals RS-422A Serial ConnectorRDB Receive Data Pin RDA Receive Data Inverted Pin SDB Send Data Pin SDA Send Data Inverted PinRS-232C/RS-422A Protocol H1 Baud rateH2 Data bits H3 Stop bitsPrescribe Frpo D0 Command H5 Protocol logicH6 Buffer nearly-full threshold H7 Buffer nearly-empty thresholdObtain a Suitable RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power requirements Power consumptionDimensions WeightGlossary Cassette mode First modeDpi dots per inch IEEE1284Prescribe commands MB mega byteMP tray OfflineUSB Universal Serial Bus Sleep modeStatus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3

Related manuals

Manual 172 pages 36.88 Kb