Kyocera FS-1010 manual Yes, Expansion Memory Installation

Page 61

Expansion Memory Installation

A.2 Expansion Memory Installation

This appendix begins by explaining how to install a DIMM (dual in-line memory module) on the main circuit board.

The FS-1010 comes supplied with 16 MB of memory installed. A slot is provided for expanding the memory in your printer so that more complex printing can be done, as well as increasing the printing speed. By installing optional DIMM into your printer, the memory in the FS-1010 can be increased to a maximum of 144 MB.

•The expansion memory should be installed only by a Kyocera Mita authorized dealer or Kyocera Mita certified technician. Kyocera Mita shall not be liable for damage due to improper installation of the expansion memory.

•The following instructions are intended for the technician only.

Notes on Handling the Main Circuit Board and DIMM

Protect the electronics by taking these precautions:

•Before touching a DIMM, touch a water pipe or other large metal object to discharge yourself of static electricity. While doing the work, it is recommended that you wear an antistatic wrist strap.

•Touch the main circuit board and DIMM only by the edges.

YES

NO

A-3

Image 61

Contents Printer Regarding Tradenames License Limited WarrantyLimitation of Remedies GeneralAgfa Japan License Agreement Guidelines Typeface Trademark AcknowledgementContents Fonts Paper SelectionAppendix a Options Appendix B Host Computer InterfaceGlossary-1 Appendix C Printer SpecificationsIndex-1 Introduction Description Guide to the ManualsGuide to the Operation Guide Basic Operations Operator Panel Keys IndicatorsReference Name Status Meaning Reference Name FunctionStatus Error Log Installation OptionsSoftware Version Hardware InformationInterface Information Toner GaugeKIR Test Pattern Maintenance Toner Container Replacement Interval Toner Container ReplacementToner Kit to be Used Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Printer Interior CleaningNever stand the process unit on end Slots in the printer Troubleshooting General Guide Symptom Check Items Corrective ActionClean the charger wire Print Quality ProblemsPrinted Results Corrective Action Contact your Kyocera Mita dealerConfirm Toner indicator Check the EcoPrint settingTry setting the thin paper mode Check the paper size settingIndicators Maintenance Messages There is no cassette in the feeder, or TheprintjobcannotbedoneatcurrentresolutionCassette is not inserted properly After reinserting the paper cassette, you should beScanner motor error 4000 error Errors Requiring Service Personnel AttentionScanner pin-photo error 4200 error Eraser error 5300 errorNone Waste toner reservoir is full Error ErrorController RAM read/write error F020 error Waste toner reservoir is fullEngine ROM check sum error F050 error Communication error F040 errorError Messages Make sure to turn the printer power off before inserting Printer power is onThis message appears when the printer is in the ready Printer has halted because you attempted to insertIndicator KM-NET for Clients display Description Normal Indicator DisplayJam at the Face-down and Face-up Trays Correcting a Paper JamJam Inside the Printer Jam at the Paper CassetteInto the printer Paper Selection Specifications Paper SpecificationsSpecification General GuidelinesCondition of the Paper Selecting the Right PaperComposition Paper Size Basis WeightPaper Sizes for Paper Feeding SmoothnessThickness Caliper Moisture ContentPaper Grain Other Paper Properties Special Paper Transparency SpecificationsTransparency overhead projection film Adhesive-backed label Adhesive-Backed LabelsEnvelopes Adhesive Label SpecificationsColored Paper Preprinted PaperRecycled Paper Paper Type Paper Source MP Tray Paper Weight Paper Type CassettePaper Type Fonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Memory CompactFlash Card Available OptionsYES Expansion Memory InstallationDimm to be used Installing the DimmInsert the Dimm into the Dimm socket so that the notches on To remove a Dimm Testing the Expansion MemorySetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Parallel Interface Interface SignalsParallel Interface Communication Modes Pin In/out Description Table B.1 Parallel Connector Pin AssignmentPaper Empty PError Pin Data 0 1 to Data 7 8 Pins 2 toReset nInit Pin Error* nFault PinSelect In nSelectIn Pin Power Ready PinUSB Interface Specifications1 RS-232C Interface Serial Interface OptionTable B.4 RS-422A Signal Pin Assignments SG Signal Ground Pin2 RS-422A Interface DTR Data Terminal Ready PinSerial Connector Overview of Signals RS-422ARDB Receive Data Pin RDA Receive Data Inverted Pin SDB Send Data Pin SDA Send Data Inverted PinH1 Baud rate RS-232C/RS-422A ProtocolH2 Data bits H3 Stop bitsH5 Protocol logic Prescribe Frpo D0 CommandH6 Buffer nearly-full threshold H7 Buffer nearly-empty thresholdRS-232C Cable Connection Connecting the Printer to the ComputerObtain a Suitable RS-232C Cable Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power consumption Power requirementsDimensions WeightGlossary First mode Cassette modeDpi dots per inch IEEE1284MB mega byte Prescribe commandsMP tray OfflineStatus Sleep modeUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3

Related manuals

Manual 172 pages 36.88 Kb