Kyocera FS-1010 manual Error Messages

Page 35

Indicators

3.3.3Error Messages

With the following errors, printing continues when you press the printer’s key. You can confirm these errors by printing a status page. (See pages

1-4and 1-5.)

Indicator

KM-NET for

Corrective Action

Clients display

File not found

The specified file is not found.

Press GO

Press the

key to resume printing. You can abondon printing

by pressing the

key.

KPDL Error

Current print processing cannot continue.

Press GO

Press the

key to resume printing. You can abandon printing

by pressing the

key.

MemoryCard err##

An error has occurred during access to the memory card

Press GO

using the PRESCRIBE RWER command or from the KM-

NET for Clients.

Look at the error code given in place of ## and refer to the

corresponding description given below.

04 :The capacity of the memory card is insufficient. Clean up

files.

05 :Specified file not on memory card.

06 :No memory for use by memory card. Expand printer memory.

Press the

key to resume printing. You can abandon printing

by pressing the

key.

Memory overflow

Printingcannotcontinuebecausethereisnotenoughmemory.

Press GO

Try adding more memory. Press the

key to resume printing.

You can abandon printing by pressing the

key.

Print overrun

Currentprintprocessingcannotcontinueduetocomplexdata.

Press GO

The data transferred to the printer was too complex to print on a

page. Press the

key to print data as far as it was stored. You

can abandon printing by the

key.

To release the page protect mode, send the following

command to the printer from the KM-NET for Clients

after this error occurs:

!R! FRPO R5, 1; EXIT;

RAM DISK error ##

Check the error code displayed in ## and refer to the

Press GO

appropriate description below.

01: Abnormal format. Try turning the power off and on again.

02: RAM disk mode is Off. Turn RAM disk mode On.

04: No disk space. Clean up files.

05: Specified file is not on disk.

06: No memory for use by disk system. Expand printer memory.

(Continued on next page)

3-11

Image 35

Contents Printer Regarding Tradenames General Limited WarrantyLicense Limitation of RemediesAgfa Japan License Agreement Guidelines Typeface Trademark AcknowledgementContents Appendix B Host Computer Interface Paper SelectionFonts Appendix a OptionsIndex-1 Appendix C Printer SpecificationsGlossary-1 Introduction Description Guide to the ManualsGuide to the Operation Guide Basic Operations Operator Panel Reference Name Function IndicatorsKeys Reference Name Status MeaningStatus Hardware Information Installation OptionsError Log Software VersionKIR Test Pattern Toner GaugeInterface Information Maintenance Toner Kit to be Used Toner Container ReplacementToner Container Replacement Interval Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Printer Interior CleaningNever stand the process unit on end Slots in the printer Troubleshooting General Guide Symptom Check Items Corrective ActionContact your Kyocera Mita dealer Print Quality ProblemsClean the charger wire Printed Results Corrective ActionCheck the paper size setting Check the EcoPrint settingConfirm Toner indicator Try setting the thin paper modeIndicators Maintenance Messages After reinserting the paper cassette, you should be TheprintjobcannotbedoneatcurrentresolutionThere is no cassette in the feeder, or Cassette is not inserted properlyEraser error 5300 error Errors Requiring Service Personnel AttentionScanner motor error 4000 error Scanner pin-photo error 4200 errorWaste toner reservoir is full ErrorNone Waste toner reservoir is full Error Controller RAM read/write error F020 errorEngine ROM check sum error F050 error Communication error F040 errorError Messages Printer has halted because you attempted to insert Printer power is onMake sure to turn the printer power off before inserting This message appears when the printer is in the readyIndicator KM-NET for Clients display Description Normal Indicator DisplayJam at the Face-down and Face-up Trays Correcting a Paper JamJam Inside the Printer Jam at the Paper CassetteInto the printer Paper Selection General Guidelines Paper SpecificationsSpecifications SpecificationComposition Selecting the Right PaperCondition of the Paper Smoothness Basis WeightPaper Size Paper Sizes for Paper FeedingPaper Grain Moisture ContentThickness Caliper Other Paper Properties Transparency overhead projection film Transparency SpecificationsSpecial Paper Adhesive-backed label Adhesive-Backed LabelsPreprinted Paper Adhesive Label SpecificationsEnvelopes Colored PaperRecycled Paper Paper Type Paper Source MP Tray Paper Weight Paper Type CassettePaper Type Fonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Memory CompactFlash Card Available OptionsYES Expansion Memory InstallationDimm to be used Installing the DimmInsert the Dimm into the Dimm socket so that the notches on To remove a Dimm Testing the Expansion MemorySetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Parallel Interface Communication Modes Interface SignalsParallel Interface Pin In/out Description Table B.1 Parallel Connector Pin AssignmentError* nFault Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Reset nInit PinSelect In nSelectIn Pin Power Ready PinUSB Interface Specifications1 RS-232C Interface Serial Interface OptionDTR Data Terminal Ready Pin SG Signal Ground PinTable B.4 RS-422A Signal Pin Assignments 2 RS-422A InterfaceSDB Send Data Pin SDA Send Data Inverted Pin Overview of Signals RS-422ASerial Connector RDB Receive Data Pin RDA Receive Data Inverted PinH3 Stop bits RS-232C/RS-422A ProtocolH1 Baud rate H2 Data bitsH7 Buffer nearly-empty threshold Prescribe Frpo D0 CommandH5 Protocol logic H6 Buffer nearly-full thresholdObtain a Suitable RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Weight Power requirementsPower consumption DimensionsGlossary IEEE1284 Cassette modeFirst mode Dpi dots per inchOffline Prescribe commandsMB mega byte MP trayUSB Universal Serial Bus Sleep modeStatus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3

Related manuals

Manual 172 pages 36.88 Kb