Kyocera FS-1010 manual Appendix a Options

Page 59

Appendix A Options

This appendix explains available options, how to expand the printer’s memory, and also how to install the memory card and the network interface card.

•Available Options

•Expansion Memory Installation

•Memory (CompactFlash) Card

•Network Interface Card

A-1

Image 59

Contents Printer Regarding Tradenames General Limited WarrantyLicense Limitation of RemediesAgfa Japan License Agreement Guidelines Typeface Trademark AcknowledgementContents Appendix B Host Computer Interface Paper SelectionFonts Appendix a OptionsIndex-1 Appendix C Printer SpecificationsGlossary-1 Introduction Description Guide to the ManualsGuide to the Operation Guide Basic Operations Operator Panel Reference Name Function IndicatorsKeys Reference Name Status MeaningStatus Hardware Information Installation OptionsError Log Software VersionKIR Test Pattern Toner GaugeInterface Information Maintenance Toner Kit to be Used Toner Container ReplacementToner Container Replacement Interval Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Printer Interior CleaningNever stand the process unit on end Slots in the printer Troubleshooting General Guide Symptom Check Items Corrective ActionContact your Kyocera Mita dealer Print Quality ProblemsClean the charger wire Printed Results Corrective ActionCheck the paper size setting Check the EcoPrint settingConfirm Toner indicator Try setting the thin paper modeIndicators Maintenance Messages After reinserting the paper cassette, you should be TheprintjobcannotbedoneatcurrentresolutionThere is no cassette in the feeder, or Cassette is not inserted properlyEraser error 5300 error Errors Requiring Service Personnel AttentionScanner motor error 4000 error Scanner pin-photo error 4200 errorWaste toner reservoir is full ErrorNone Waste toner reservoir is full Error Controller RAM read/write error F020 errorEngine ROM check sum error F050 error Communication error F040 errorError Messages Printer has halted because you attempted to insert Printer power is onMake sure to turn the printer power off before inserting This message appears when the printer is in the readyIndicator KM-NET for Clients display Description Normal Indicator DisplayJam at the Face-down and Face-up Trays Correcting a Paper JamJam Inside the Printer Jam at the Paper CassetteInto the printer Paper Selection General Guidelines Paper SpecificationsSpecifications SpecificationComposition Selecting the Right PaperCondition of the Paper Smoothness Basis WeightPaper Size Paper Sizes for Paper FeedingPaper Grain Moisture ContentThickness Caliper Other Paper Properties Transparency overhead projection film Transparency SpecificationsSpecial Paper Adhesive-backed label Adhesive-Backed LabelsPreprinted Paper Adhesive Label SpecificationsEnvelopes Colored PaperRecycled Paper Paper Type Paper Source MP Tray Paper Weight Paper Type CassettePaper Type Fonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Memory CompactFlash Card Available OptionsYES Expansion Memory InstallationDimm to be used Installing the DimmInsert the Dimm into the Dimm socket so that the notches on To remove a Dimm Testing the Expansion MemorySetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Parallel Interface Communication Modes Interface SignalsParallel Interface Pin In/out Description Table B.1 Parallel Connector Pin AssignmentError* nFault Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Reset nInit PinSelect In nSelectIn Pin Power Ready PinUSB Interface Specifications1 RS-232C Interface Serial Interface OptionDTR Data Terminal Ready Pin SG Signal Ground PinTable B.4 RS-422A Signal Pin Assignments 2 RS-422A InterfaceSDB Send Data Pin SDA Send Data Inverted Pin Overview of Signals RS-422ASerial Connector RDB Receive Data Pin RDA Receive Data Inverted PinH3 Stop bits RS-232C/RS-422A ProtocolH1 Baud rate H2 Data bitsH7 Buffer nearly-empty threshold Prescribe Frpo D0 CommandH5 Protocol logic H6 Buffer nearly-full thresholdObtain a Suitable RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Weight Power requirementsPower consumption DimensionsGlossary IEEE1284 Cassette modeFirst mode Dpi dots per inchOffline Prescribe commandsMB mega byte MP trayUSB Universal Serial Bus Sleep modeStatus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3

Related manuals

Manual 172 pages 36.88 Kb