Kyocera FS-1010 manual Status

Page 14

Operator Panel

The following is the printout of a typical standard status page. Its contents are explained in detail on the next page.

		FS-1010 Page Printer
	STATUS PAGE		1
	Firmware Version:	Released:

Hardware Information	Memory
2			5

3	Page Information	Installed Options
		6

4	Network Status	Emulation

		7
	Error Log	8
	Error Log
	Toner Gauge
		9
	0	100
	Interfaces
10
11	KIR Test pattern	ON

Items and values on the status page may vary depending on the printer’s firmware version.

1-4

Image 14

Contents Printer Regarding Tradenames Limitation of Remedies Limited WarrantyLicense GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Appendix a Options Paper SelectionFonts Appendix B Host Computer InterfaceIndex-1 Appendix C Printer SpecificationsGlossary-1 Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Reference Name Status Meaning IndicatorsKeys Reference Name FunctionStatus Software Version Installation OptionsError Log Hardware InformationKIR Test Pattern Toner GaugeInterface Information Maintenance Toner Kit to be Used Toner Container ReplacementToner Container Replacement Interval Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Cleaning Printer InteriorNever stand the process unit on end Slots in the printer Troubleshooting Symptom Check Items Corrective Action General GuidePrinted Results Corrective Action Print Quality ProblemsClean the charger wire Contact your Kyocera Mita dealerTry setting the thin paper mode Check the EcoPrint settingConfirm Toner indicator Check the paper size settingIndicators Maintenance Messages Cassette is not inserted properly TheprintjobcannotbedoneatcurrentresolutionThere is no cassette in the feeder, or After reinserting the paper cassette, you should beScanner pin-photo error 4200 error Errors Requiring Service Personnel AttentionScanner motor error 4000 error Eraser error 5300 errorController RAM read/write error F020 error ErrorNone Waste toner reservoir is full Error Waste toner reservoir is fullCommunication error F040 error Engine ROM check sum error F050 errorError Messages This message appears when the printer is in the ready Printer power is onMake sure to turn the printer power off before inserting Printer has halted because you attempted to insertNormal Indicator Display Indicator KM-NET for Clients display DescriptionCorrecting a Paper Jam Jam at the Face-down and Face-up TraysJam at the Paper Cassette Jam Inside the PrinterInto the printer Paper Selection Specification Paper SpecificationsSpecifications General GuidelinesComposition Selecting the Right PaperCondition of the Paper Paper Sizes for Paper Feeding Basis WeightPaper Size SmoothnessPaper Grain Moisture ContentThickness Caliper Other Paper Properties Transparency overhead projection film Transparency SpecificationsSpecial Paper Adhesive-Backed Labels Adhesive-backed labelColored Paper Adhesive Label SpecificationsEnvelopes Preprinted PaperRecycled Paper Paper Type Paper Source MP Tray Paper Weight Paper Type CassettePaper Type Fonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Memory CompactFlash CardExpansion Memory Installation YESInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Testing the Expansion Memory To remove a DimmSetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Parallel Interface Communication Modes Interface SignalsParallel Interface Table B.1 Parallel Connector Pin Assignment Pin In/out DescriptionReset nInit Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Error* nFault PinPower Ready Pin Select In nSelectIn PinSpecifications USB InterfaceSerial Interface Option 1 RS-232C Interface2 RS-422A Interface SG Signal Ground PinTable B.4 RS-422A Signal Pin Assignments DTR Data Terminal Ready PinRDB Receive Data Pin RDA Receive Data Inverted Pin Overview of Signals RS-422ASerial Connector SDB Send Data Pin SDA Send Data Inverted PinH2 Data bits RS-232C/RS-422A ProtocolH1 Baud rate H3 Stop bitsH6 Buffer nearly-full threshold Prescribe Frpo D0 CommandH5 Protocol logic H7 Buffer nearly-empty thresholdObtain a Suitable RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Dimensions Power requirementsPower consumption WeightGlossary Dpi dots per inch Cassette modeFirst mode IEEE1284MP tray Prescribe commandsMB mega byte OfflineUSB Universal Serial Bus Sleep modeStatus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3

Related manuals

Manual 172 pages 36.88 Kb