Kyocera FS-1010 manual Adhesive Label Specifications, Envelopes, Colored Paper, Preprinted Paper

Page 49

Special Paper

Table 4.4 lists the specifications for adhesive label paper.

Table 4.4 Adhesive Label Specifications

Item

Specification

Weight of top sheet

44 to 74 g/m2 (12 to 20 lb/ream)

Composite weight

104 to 151 g/m2 (28 to 40 lb/ream)

Thickness of top sheet

0.086 to 0.107 mm (3.9 to 4.2 mils)

 

 

Composite thickness

0.115 to 0.145 mm (4.5 to 5.7 mils)

 

 

Moisture content

4 to 6% (composite)

 

 

Envelopes

The printer can print on envelopes using paper with a basis weight of 60 to 79 g/m2 (16 to 21 lb/ream). Envelopes must be manually fed.

An envelope is a more complex object than a single sheet of paper. For this reason, it may not be possible to obtain consistent printing quality over the entire envelope surface.

Many envelopes have a diagonal grain orientation. (See Paper Grain on page 4-5.) This orientation is more likely to wrinkle and crease on its way through the printer. Before purchasing envelopes for use with the printer, test a sample to verify the envelope’s suitability.

Do not use envelopes that have an encapsulated liquid adhesive.

Avoid long printing runs consisting of envelopes only. Extensive envelope printing can cause premature printer wear.

To avoid jamming due to curled envelopes, do not leave more than approximately 10 printed envelopes stacked in the paper trays during multiple envelope printing.

Colored Paper

Colored paper should satisfy the same conditions as white bond paper, listed in Table 4.1 on page 4-2. In addition, the pigments used in the paper must be able to withstand the heat of fusing during the printing process (up to 200°C or 392°F).

Preprinted Paper

Preprinted paper should have a bond paper base. The preprinted ink must be able to withstand the heat of fusing during the printing process, and must not be affected by silicone oil.

Do not use paper with any kind of surface treatment, such as the type of paper commonly used for calendars.

4-9

Image 49
Contents Printer Regarding Tradenames License Limited WarrantyLimitation of Remedies GeneralAgfa Japan License Agreement Guidelines Typeface Trademark AcknowledgementContents Fonts Paper SelectionAppendix a Options Appendix B Host Computer InterfaceGlossary-1 Appendix C Printer SpecificationsIndex-1 Introduction Description Guide to the ManualsGuide to the Operation Guide Basic Operations Operator Panel Keys IndicatorsReference Name Status Meaning Reference Name FunctionStatus Error Log Installation OptionsSoftware Version Hardware InformationInterface Information Toner GaugeKIR Test Pattern Maintenance Toner Container Replacement Interval Toner Container ReplacementToner Kit to be Used Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Printer Interior CleaningNever stand the process unit on end Slots in the printer Troubleshooting General Guide Symptom Check Items Corrective ActionClean the charger wire Print Quality ProblemsPrinted Results Corrective Action Contact your Kyocera Mita dealerConfirm Toner indicator Check the EcoPrint settingTry setting the thin paper mode Check the paper size settingIndicators Maintenance Messages There is no cassette in the feeder, or TheprintjobcannotbedoneatcurrentresolutionCassette is not inserted properly After reinserting the paper cassette, you should beScanner motor error 4000 error Errors Requiring Service Personnel AttentionScanner pin-photo error 4200 error Eraser error 5300 errorNone Waste toner reservoir is full Error ErrorController RAM read/write error F020 error Waste toner reservoir is fullEngine ROM check sum error F050 error Communication error F040 errorError Messages Make sure to turn the printer power off before inserting Printer power is onThis message appears when the printer is in the ready Printer has halted because you attempted to insertIndicator KM-NET for Clients display Description Normal Indicator DisplayJam at the Face-down and Face-up Trays Correcting a Paper JamJam Inside the Printer Jam at the Paper CassetteInto the printer Paper Selection Specifications Paper SpecificationsSpecification General GuidelinesCondition of the Paper Selecting the Right PaperComposition Paper Size Basis WeightPaper Sizes for Paper Feeding SmoothnessThickness Caliper Moisture ContentPaper Grain Other Paper Properties Special Paper Transparency SpecificationsTransparency overhead projection film Adhesive-backed label Adhesive-Backed LabelsEnvelopes Adhesive Label SpecificationsColored Paper Preprinted PaperRecycled Paper Paper Type Paper Source MP Tray Paper Weight Paper Type CassettePaper Type Fonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Memory CompactFlash Card Available OptionsYES Expansion Memory InstallationDimm to be used Installing the DimmInsert the Dimm into the Dimm socket so that the notches on To remove a Dimm Testing the Expansion MemorySetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Parallel Interface Interface SignalsParallel Interface Communication Modes Pin In/out Description Table B.1 Parallel Connector Pin AssignmentPaper Empty PError Pin Data 0 1 to Data 7 8 Pins 2 toReset nInit Pin Error* nFault PinSelect In nSelectIn Pin Power Ready PinUSB Interface Specifications1 RS-232C Interface Serial Interface OptionTable B.4 RS-422A Signal Pin Assignments SG Signal Ground Pin2 RS-422A Interface DTR Data Terminal Ready PinSerial Connector Overview of Signals RS-422ARDB Receive Data Pin RDA Receive Data Inverted Pin SDB Send Data Pin SDA Send Data Inverted PinH1 Baud rate RS-232C/RS-422A ProtocolH2 Data bits H3 Stop bitsH5 Protocol logic Prescribe Frpo D0 CommandH6 Buffer nearly-full threshold H7 Buffer nearly-empty thresholdRS-232C Cable Connection Connecting the Printer to the ComputerObtain a Suitable RS-232C Cable Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power consumption Power requirementsDimensions WeightGlossary First mode Cassette modeDpi dots per inch IEEE1284MB mega byte Prescribe commandsMP tray OfflineStatus Sleep modeUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3
Related manuals
Manual 172 pages 36.88 Kb