Kyocera FS-1010 manual To remove a Dimm, Testing the Expansion Memory

Page 64

Expansion Memory Installation

7 Close the clips on the DIMM slot to secure the DIMM.

8

When you have finished installing the DIMM, replace the side cover

and fasten it with the screw.

To remove a DIMM:

Remove the side cover as shown in steps 1 to 3 on page A-4, then carefully pull the end clips outwards and pull the DIMM out of the socket.

Testing the Expansion Memory

After you have finished installing DIMM in the printer, test the printer to see if installation succeeded.

To test the expansion memory, proceed as follows:

1

Make sure the power switch is off. Plug the power cord into the

printer and turn on the power.

 

2

When the printer is online, press and hold the

key for 3 seconds

or more.

 

3

If the installation succeeded, the amount of memory shown on the

status page will correspond with the amount of expansion memory.

(The factory installed memory size is 16 MB.)

A-6

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Printer Regarding Tradenames Limited Warranty LicenseLimitation of Remedies GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Paper Selection FontsAppendix a Options Appendix B Host Computer InterfaceGlossary-1 Appendix C Printer SpecificationsIndex-1 Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Indicators KeysReference Name Status Meaning Reference Name FunctionStatus Installation Options Error LogSoftware Version Hardware InformationInterface Information Toner GaugeKIR Test Pattern Maintenance Toner Container Replacement Interval Toner Container ReplacementToner Kit to be Used Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Cleaning Printer InteriorNever stand the process unit on end Slots in the printer Troubleshooting Symptom Check Items Corrective Action General GuidePrint Quality Problems Clean the charger wirePrinted Results Corrective Action Contact your Kyocera Mita dealerCheck the EcoPrint setting Confirm Toner indicatorTry setting the thin paper mode Check the paper size settingIndicators Maintenance Messages Theprintjobcannotbedoneatcurrentresolution There is no cassette in the feeder, orCassette is not inserted properly After reinserting the paper cassette, you should beErrors Requiring Service Personnel Attention Scanner motor error 4000 errorScanner pin-photo error 4200 error Eraser error 5300 errorError None Waste toner reservoir is full ErrorController RAM read/write error F020 error Waste toner reservoir is fullCommunication error F040 error Engine ROM check sum error F050 errorError Messages Printer power is on Make sure to turn the printer power off before insertingThis message appears when the printer is in the ready Printer has halted because you attempted to insertNormal Indicator Display Indicator KM-NET for Clients display DescriptionCorrecting a Paper Jam Jam at the Face-down and Face-up TraysJam at the Paper Cassette Jam Inside the PrinterInto the printer Paper Selection Paper Specifications SpecificationsSpecification General GuidelinesCondition of the Paper Selecting the Right PaperComposition Basis Weight Paper SizePaper Sizes for Paper Feeding SmoothnessThickness Caliper Moisture ContentPaper Grain Other Paper Properties Special Paper Transparency SpecificationsTransparency overhead projection film Adhesive-Backed Labels Adhesive-backed labelAdhesive Label Specifications EnvelopesColored Paper Preprinted PaperRecycled Paper Paper Type Paper Source MP Tray Paper Weight Paper Type CassettePaper Type Fonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Memory CompactFlash CardExpansion Memory Installation YESInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Testing the Expansion Memory To remove a DimmSetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Parallel Interface Interface SignalsParallel Interface Communication Modes Table B.1 Parallel Connector Pin Assignment Pin In/out DescriptionData 0 1 to Data 7 8 Pins 2 to Paper Empty PError PinReset nInit Pin Error* nFault PinPower Ready Pin Select In nSelectIn PinSpecifications USB InterfaceSerial Interface Option 1 RS-232C InterfaceSG Signal Ground Pin Table B.4 RS-422A Signal Pin Assignments2 RS-422A Interface DTR Data Terminal Ready PinOverview of Signals RS-422A Serial ConnectorRDB Receive Data Pin RDA Receive Data Inverted Pin SDB Send Data Pin SDA Send Data Inverted PinRS-232C/RS-422A Protocol H1 Baud rateH2 Data bits H3 Stop bitsPrescribe Frpo D0 Command H5 Protocol logicH6 Buffer nearly-full threshold H7 Buffer nearly-empty thresholdRS-232C Cable Connection Connecting the Printer to the ComputerObtain a Suitable RS-232C Cable Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power requirements Power consumptionDimensions WeightGlossary Cassette mode First modeDpi dots per inch IEEE1284Prescribe commands MB mega byteMP tray OfflineStatus Sleep modeUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3
Related manuals
Manual 172 pages 36.88 Kb
Top Page Image Contents