Kyocera FS-1010 Print Quality Problems, Printed Results Corrective Action, Clean the charger wire

Page 27

Print Quality Problems

3.2Print Quality Problems

	As the following table shows, there are many possible causes of print
	quality problems, such as blank output as. The troubleshooting procedure
	for each type of problem is explained below. If you still can not solve the
	problem, contact your Kyocera Mita dealer.

Printed Results	Corrective Action
All-black printout	Contact your Kyocera Mita dealer.

Dropouts, horizontal streaks, stray dots	Clean the charger wire.
	Open the printer’s top and front covers. Remove the
	process unit from the printer and slide the charger knob
	back and forth to clean the charger wire.
	(See Chapter 2)

Black or white vertical streaks	Check the operator panel.
	When the	(toner) indicator flashes, install a new
	toner kit. Clean the printer after replacement.
	(See Chapter 2)

Clean the charger wire.

Open the printer’s top and front covers. Remove the process unit from the printer and slide the charger knob back and forth to clean the charger wire.

(See Chapter 2)

Check the position of the charger cleaner knob Open the printer’s top and front covers. Remove the process unit from the printer. Make sure the charger cleaner knob is restored to its home position.

(See Chapter 2)

(Continued on next page)

3-3

Image 27

Contents Printer Regarding Tradenames General Limited WarrantyLicense Limitation of RemediesAgfa Japan License Agreement Guidelines Typeface Trademark AcknowledgementContents Appendix B Host Computer Interface Paper SelectionFonts Appendix a OptionsAppendix C Printer Specifications Glossary-1Index-1 Introduction Description Guide to the ManualsGuide to the Operation Guide Basic Operations Operator Panel Reference Name Function IndicatorsKeys Reference Name Status MeaningStatus Hardware Information Installation OptionsError Log Software VersionToner Gauge Interface InformationKIR Test Pattern Maintenance Toner Container Replacement Toner Container Replacement IntervalToner Kit to be Used Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Printer Interior CleaningNever stand the process unit on end Slots in the printer Troubleshooting General Guide Symptom Check Items Corrective ActionContact your Kyocera Mita dealer Print Quality ProblemsClean the charger wire Printed Results Corrective ActionCheck the paper size setting Check the EcoPrint settingConfirm Toner indicator Try setting the thin paper modeIndicators Maintenance Messages After reinserting the paper cassette, you should be TheprintjobcannotbedoneatcurrentresolutionThere is no cassette in the feeder, or Cassette is not inserted properlyEraser error 5300 error Errors Requiring Service Personnel AttentionScanner motor error 4000 error Scanner pin-photo error 4200 errorWaste toner reservoir is full ErrorNone Waste toner reservoir is full Error Controller RAM read/write error F020 errorEngine ROM check sum error F050 error Communication error F040 errorError Messages Printer has halted because you attempted to insert Printer power is onMake sure to turn the printer power off before inserting This message appears when the printer is in the readyIndicator KM-NET for Clients display Description Normal Indicator DisplayJam at the Face-down and Face-up Trays Correcting a Paper JamJam Inside the Printer Jam at the Paper CassetteInto the printer Paper Selection General Guidelines Paper SpecificationsSpecifications SpecificationSelecting the Right Paper Condition of the PaperComposition Smoothness Basis WeightPaper Size Paper Sizes for Paper FeedingMoisture Content Thickness CaliperPaper Grain Other Paper Properties Transparency Specifications Special PaperTransparency overhead projection film Adhesive-backed label Adhesive-Backed LabelsPreprinted Paper Adhesive Label SpecificationsEnvelopes Colored PaperRecycled Paper Paper Source MP Tray Paper Weight Paper Type Cassette Paper TypePaper Type Fonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Memory CompactFlash Card Available OptionsYES Expansion Memory InstallationDimm to be used Installing the DimmInsert the Dimm into the Dimm socket so that the notches on To remove a Dimm Testing the Expansion MemorySetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Interface Signals Parallel InterfaceParallel Interface Communication Modes Pin In/out Description Table B.1 Parallel Connector Pin AssignmentError* nFault Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Reset nInit PinSelect In nSelectIn Pin Power Ready PinUSB Interface Specifications1 RS-232C Interface Serial Interface OptionDTR Data Terminal Ready Pin SG Signal Ground PinTable B.4 RS-422A Signal Pin Assignments 2 RS-422A InterfaceSDB Send Data Pin SDA Send Data Inverted Pin Overview of Signals RS-422ASerial Connector RDB Receive Data Pin RDA Receive Data Inverted PinH3 Stop bits RS-232C/RS-422A ProtocolH1 Baud rate H2 Data bitsH7 Buffer nearly-empty threshold Prescribe Frpo D0 CommandH5 Protocol logic H6 Buffer nearly-full thresholdConnecting the Printer to the Computer RS-232C Cable ConnectionObtain a Suitable RS-232C Cable Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Weight Power requirementsPower consumption DimensionsGlossary IEEE1284 Cassette modeFirst mode Dpi dots per inchOffline Prescribe commandsMB mega byte MP traySleep mode StatusUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3

Related manuals

Manual 172 pages 36.88 Kb