NEC RS-232C user manual Sync, Dvi-Pc Dvi-Hd, Ntsc, Secam, Unmute Mute MTS

Page 48

	Item		OP	OP code	Parameter	Remarks
			code
			page
		SYNC	02h	E1h	1: Hi(2.2kohm)
		Terminate			2: Lo(75ohm)
	DVI Mode		02h	CFh	1: DVI-PC
					2: DVI-HD
	BNC Mode		10h	7Eh	0: No operate
					1: RGB
					2: Component
					3: Video
	SCART Mode		02h	9Eh	0: Off
					1: On
	HDMI Signal		10h	40h	0: None
					1: Expand
					2: Raw
	Scan Conversion		02h	25h	1: Off(INTERLACE)
					2: Enable
					(IP ON/PROGRESSIVE)
	Color System		02h	21h	1: NTSC
					2: PAL
					3: SECAM
					4: Auto
					5: 4.43NTSC
					6: PAL-60
	Scan Mode		02h	E3h	1: Under Scan
					2: Over Scan
	Menu tree reset		02h	CBh	0: None	Momentary
	(Advanced Option)				10: Reset Advanced
					option category
	Menu tree reset		02h	CBh	0: None	Momentary
	(Factory reset)				1: Factory Reset
	Input		00h	60h	0: No mean
					1: VGA
					2: RGB/HV
					3: DVI
					4: HDMI (Set only)
					5: Video1
					6: Video2
					7: S-Video
					10: TV
					12: DVD/HD1
					13: Option
					14: DVD/HD2
					15: Display Port
					17: HDMI
	Audio Input		02h	2Eh	1: Audio 1(PC)
					2: Audio 2
					3: Audio 3
					4: HDMI
					6: TV/Option
					7: Display Port
	Volume UP/Down		00h	62h	0: whisper

					100: loud
	Mute		00h	8Dh	0,2: UNMUTE
					1: MUTE
	MTS		02h	2Ch	0: None	This
					1: Main	operation
					2: Sub	requires
					3: Main + Sub	supported	TV
						option	TV
						tuner.
	Sound		02h	34h	1: Off	Not available
					2: Low (or On)	on X461UN.
					3: High (or On)

(48/50)

Image 48

Contents Connectors and wiring ApplicationCommunication Parameter Communication Format Header block format fixed lengthALL Message block format STXETX STX ETX MSB LSBCheck code MSB LSBSOH Delimiter Following is an example of a Check code BCC calculationMessage type Get current Parameter from a monitorSet parameter Set parameter reply Current conditionCommands Save Current SettingsGet Timing Report and Timing reply MSB LSB ETXTypical procedure example How to change the Brightness settingNull Message BCCHeader Message Check code Delimiter Message Check code Delimiter Code STX-0-0-0-2-7-9-0-0 Power control procedure Power status readPower control Controller requests the monitor to control monitor powerAsset Data read and write Asset Data Read Request and replyAsset Data write Date & Time read and write Date & Time ReadBCC DS-ETX Date & Time Write Check code Delimiter Schedule read and write Schedule ReadSTX-C-3-2-1-PG-ON HOUR-ON MIN Page BCC OFF HOUR-OFF MIN-INPUT-WD-FL-ETX B33h, 42h 59 =3Bh C33h, 43h Off timer isn’t set Schedule WritePG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P Mode Page BCC OFF HOUR-OFF MIN-INPUT-WD-FL-P Mode Header 31/50 SOH-0-0-Monitor ID-B-0-C STX-C-3-1-5-ST-PG-EN-ETX STX-C-2-1-4-PG-ON HOUR-ON MIN 34/50 BCC Self diagnosis Self-diagnosis status readST Result of self-tests 0-030h, 30h00 Normal Serial No. & Model Name Read Serial No. ReadModel Name Read Security Lock Security Lock Control930h, 39h Page Dicom SIM ISFAdjust Surround HdmiPOP RGB/HVPIP OSD Option Sync DVI-PC DVI-HDNtsc SecamPIP ON/OFF All data are subject to change without notice

Related manuals

Manual 72 pages 50.57 Kb