This command is used in order to write the setting of the Schedule.
1) The controller requests the monitor to write Schedule.
Header | Message | Check code | Delimiter |
SOH-'0'-Monitor ID-'0'-'A'-'2'-'6' | STX-'C'-'2'-'2'-'2'-PG-ON HOUR-ON MIN- | BCC | CR |
| OFF HOUR-OFF MIN-INPUT-WD-FL-P MODE- | | |
| EXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7-ETX | | |
Header | | | |
SOH (01h): Start Of Header | | |
'0' (30h): Reserved | | | |
Monitor ID: Specify the Monitor ID of which you want to change a setting. | |
Ex.) If Monitor ID is '1', specify 'A'. | | |
'0' (30h): Message sender is the controller. | | |
'A' (41h): Message type is "Command". | | |
'2'-'6'(32h, 36h): Message length. | | |
Message | | | |
STX (02h): Start of Message | | |
'C'-'2'-'2'-'2' (43h, 32h, 32h, 32h): Schedule writes command | | |
PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P MODE | | |
EXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7: Schedule data | | |
PG: Program No. | | | |
'0'-'0'(30h, 30h): Program No.1 | | |
| | | |
'0'-'6'(30h, 36h): Program No.7 | | |
ON_HOUR: Turn on time (hour) '0'-'0'(30h, 30h): 00
'1'-'7'(31h, 37h): 23 (=17h)
'1'-'8'(31h, 38h): ON timer isn't set.
ON_MIN: Turn on time (minute) '0'-'0'(30h, 30h): 0
'3'-'B'(33h, 42h): 59
'3'-'C'(33h, 43h): On timer isn’t set.
OFF_HOUR: Turn off time (hour) '0'-'0'(30h, 30h): 00
'1'-'7'(31h, 37h): 23 (=17h)
'1'-'8'(31h, 38h): Off timer isn't set.
OFF_MIN: Turn off time (minute) '0'-'0'(30h, 30h): 0
'3'-'B'(33h, 42h): 59 (=3Bh)
'3'-'C'(33h, 43h): Off timer isn’t set.
INPUT: Timer input
'0'-'0'(30h,30h): No mean (works on last memory)
'0'-'1'(30h,31h): VGA
'0'-'2'(30h,32h): RGB/HV
'0'-'3'(30h,33h): DVI
'0'-'4'(30h,34h): HDMI (Set only)
'0'-'5'(30h,35h): Video1
'0'-'6'(30h,36h): Video2
'0'-'7'(30h,37h): S-Video
'0'-'A'(30h,41h): TV
'0'-'C'(30h,43h): DVD/HD1
'0'-'D'(30h,44h): Option
'0'-'E'(30h,45h): DVD/HD2
'0'-'F'(30h,46h): Display Port
'1'-'1'(31h,31h): HDMI
*Please select active input on your system (setting).
*If you select inactive input here, the input change execution will be ignored.
