Emerson ATCA-7350 manual System Boot Options Parameter #96, System Boot Options Parameter #98

Page 20

Supported Commands

Chassis Device Commands

 

 

2.1.7.1.2System Boot Options Parameter #96

This boot parameter is an Emerson-specific OEM boot parameter. Its definition is given in the following table.

Table 2-10 System Boot Options Parameter #96

Boot Option

 

Parameter Data

Description

 

 

1

This parameter specifies the processor ID for which the boot option is to be set.

 

This parameter has to be 0 always for this blade.

 

 

2

This parameter is used to select the BIOS boot bank of which the payload shall

 

boot from:

 

[7:1] Reserved

 

[0] Default/backup boot flash selection

 

 

There is no Set Selector or Block Selector with this command.

The System Boot Options parameter #96 is non-volatile. Its parameter data remains preserved after IPMC power cycles and firmware upgrades.

2.1.7.1.3System Boot Options Parameter #98

This boot parameter is an Emerson-specific OEM parameter.

This timer specifies how long the IPMC waits for the payload to shut down gracefully. If the payload software does not configure its OpenIPMI library to be notified for graceful shutdown requests, the IPMC shuts down the payload when the timer expires.

Table 2-11 System Boot Options Parameter #98

Boot Option Parameter

 

Data

Description

 

 

1

This parameter specifies the Graceful Shutdown Timeout LSB (given in

 

100 msec)

 

 

2

This parameter specifies the Graceful Shutdown Timeout MSB (given in

 

100 msec)

 

 

20

ATCA-7350 Control via IPMI Programmer’s Reference (6806800H29E)

Image 20
Contents ATCA-7350 Control via Ipmi Contact Address Contents SOL Module Configuration ContentsResponse Data of Set Serial Output Command List of TablesList of Tables Abbreviations Overview of ContentsAbout this Manual Conventions About this Manual Abbreviation DefinitionNotation Description BoldSummary of Changes Comments and SuggestionsAbout this Manual Part Number Publication Date DescriptionAbout this Manual Feature Description 1 HPM.1 Specific Firmware UpgradesFeatures IntroductionIpmc Firmware Upgrade Introduction HPM.1 Specific Firmware UpgradesGraceful Shutdown Timeout Serial over LANSensors MAC Address RecordBoot Configuration Parameters Local System Event LogExternal Watchdog Introduction Local System Event LogSupported Commands Standard Ipmi CommandsGlobal Ipmi Commands System Interface CommandsWatchdog Commands SEL Device CommandsSupported Watchdog Commands Supported SEL Device CommandsFRU Inventory Commands Sensor Device CommandsSupported FRU Inventory Commands Supported Sensor Device CommandsChassis Device Commands Supported Chassis Device CommandsConfigurable System Boot Option Parameters Supported Commands Chassis Device CommandsData Byte Description System Boot Options Parameter #5Chassis Device Commands Supported Commands Boot Option Parameter Data Description 10 System Boot Options Parameter #9611 System Boot Options Parameter #98 LAN Device Commands 12 System Boot Options Parameter #9913 Supported LAN Device Commands LAN Device Commands Supported CommandsSupported Commands Picmg 3.0 Commands Picmg 3.0 Commands14 Supported Picmg 3.0 Commands Emerson Specific Commands Serial Output Commands15 Serial Output Commands Emerson Specific CommandsSupported Commands16 Request Data of Set Serial Output Command 17 Response Data of Set Serial Output CommandSupported Commands Serial Output Commands Byte Data FieldSerial Output Commands Supported Commands 18 Request Data of Get Serial Output Command19 Response Data of Get Serial Output Command Page Area Description Value Access FRU Information and Sensor Data RecordsFRU Information MAC Address RecordInterface Type Assignments Emerson MAC Address RecordEmerson MAC Address Descriptor Sensor Data Records FRU Information and Sensor Data Records Sensor Data RecordsIpmi Sensors Overview +3.3VCC Sensor Feature Raw Value Description+12VCC Sensor +3.3VSB Sensor Sensor Data RecordsFRU Information and Sensor Data Records+5VCC Sensor FRU Information and Sensor Data RecordsSensor Data Records10 +5VSB Sensor 11 -48V Power1 Sensor 12 -48V Power2 Sensor13 Acpi State Sensor 14 Bios Bank Sensor 15 BMC Post Error Sensor16 Boot Errors Sensor 17 CPU0 Core Rem Sensor 18 CPU0 Status Sensor 19 CPU1 Core Rem Sensor20 CPU1 Status Sensor 21 CPU Inlet Temp Sensor 22 FBD Inlet Temp Sensor 23 FRU Hot Swap Sensor24 FW Progress Sensor 25 Handle State Sensor 26 HD Env Temp Sensor27 Ipmb Link State Sensor 28 Log Disabled Sensor 29 PwrOk Sig. Drop Sensor 30 RTM Handle Sensor31 RTM HS Sensor 32 System Restart Sensor 33 Ver Change Sensor34 Watchdog Sensor 34 Watchdog Sensor Page Introduction SOL Module ConfigurationConfigure the SOL Enable SOL Load SOL Module Configuration Enable SOL LoadSetup SOL Session SOL Module Configuration Setup SOL SessionQuery the Configuration of SOL SOL Module Configuration Query the Configuration of SOL =OEMConfigure the SOL Module in OS Configure the SOL Module in OS SOL Module ConfigurationPage Emerson Network Power Embedded Computing Documents Related SpecificationsTable A-2 Related Specifications Related Documentation