Philips EPIA-MII user manual COM2 The Second Serial Port, Floppy Disk Drive Connector FDD

Page 30

				Installation
COM2: The Second Serial Port
COM2 is a pin header for second serial port.				9
Pin	Signal	Description
1	DCD	Data Carry Detect
2	SIN	Serial In or Receive Data	2	1
3	SOUT	Serial Out or Transmit Data		COM2
4	DTR	Data Terminal Ready
5	GND	Ground
6	DSR	Data Set Ready
7	RTS	Request To Send
8	CTS	Clear To Send		CLE266
9	RI	Ring Indicate

Floppy Disk Drive Connector: FDD

The floppy disk drive connector supports 360K, 720K, 1.2M. 1.44M, and 2.88M floppy disk types.

CLE266

2-15

Image 30

Contents User’s Manual Copyright TrademarksDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Onboard I/O Connectors Back Panel I/O PortsForm Factor Mainboard Layout Back PanelPlacement of Add-On Module Add-On ModuleBack Panel Ports SlotsOnboard Connectors and Jumpers Connecter/Jumper DescriptionChapter Installation CPU VIA C3TM E-Series ProcessorVIA Eden Processor Memory Module Installation DDR Sdram Module Installation ProceduresAvailable DDR Sdram Configurations Connecting the Power Supply ATX 20-Pin Power ConnectorMouse Port PS2MS Keyboard Port PS2KBRJ45 10/100 NIC Port VGA OutUSB Ports Video PortIeee 1394 Port Serial Port COM1Card Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone IDE1 Primary IDE Connector ConnectorsHard Disk Connectors IDE1 & IDE2 IDE2 Secondary IDE ConnectorCase Connector Fpanel Power LED PWR LEDSpeaker IrDA Infrared Module Connector FIR Consumer Infrared Module / PS2 Header KbmsUSB pin-header USB3/4 Wake-on LAN WOLFloppy Disk Drive Connector FDD COM2 The Second Serial PortCD Audio Connector Cdin Front Audio Panel FaudioSMBus Connector SMBus LPT Pin Header LPTPort Connector Lvds Connector OptionalJumpers Clear Cmos ClearcmosRCA Video or S/PDIF Select Spdifsel Peripheral Component Interconnect PCI PCI Interrupt Request RoutingBios Setup Entering Setup Control KeysSub-Menu Getting HelpMain Menu General Help F1Main Menu Set Supervisor Password Load Fail-Safe DefaultsLoad Optimized Defaults Set User PasswordTime Standard Cmos FeaturesDate Drive A/BIDE Primary Master/Slave, Secondary Master/Slave Virus Warning Advanced Bios FeaturesQuick Power On Self Test CPU L2 Cache ECC CheckingBoot Up Floppy Seek First/Second/Third Boot DeviceBoot Other Device Swap Floppy DriveTypematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting Typematic Rate Chars/SecShow Summary Information Display Small LogoAdvanced Chipset Features AGP Mode InternalAGP Aperture Size CPU to PCI Post Write CPU Direct Access FBAGP Fast Write Select Display DeviceOnboard IDE Channel 1/2 IDE Prefetch ModeIntegrated Peripherals Display Card PriorityVIA OnChip LAN Onboard Lan Boot ROMAC97 Audio OnChip USB ControllerOnboard FDC Controller Parallel Port ModeSuperIO Device Onboard Serial Port 1/2Onboard Fast IR EPP Mode SelectECP Mode Use DMA Fast IR IRQPower Management Setup HDD Power DownAcpi Suspend Type Run Vgabios if S3 Resume Power Management TimerPower Off by Pwrbtn Video Off OptionPeripheral Activities RTC Alarm Resume PowerOn by PCI CardWake On LAN/Ring Connector PS2MS Wakeup from S3/S4/S5IRQs Activities Primary IntrReset Configuration Data PNP/PCI ConfigurationsPNP OS Installed Resource Controlled ByAssign IRQ For VGA/USB IRQ Resources PC Health Status Dram Timing Frequency / Voltage ControlDram Clock Dram CAS LatencyPrecharge to Active Trp Dram Command RateBank Interleave Active to Precharge TrasDram Voltage CPU ClockSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Driver Utilities Getting StartedRunning the Driver Utilities CD CD Content Chapter