Philips EPIA-MII user manual Case Connector Fpanel, Power LED PWR LED, Speaker

Page 27

Chapter 2

Case Connector: F_PANEL

The F_PANEL connector block allows you to connect to the power switch, reset switch, power LED, HDD LED, SLED and the Speaker on the case.

Pin	Signal	Pin	Signal
1	PWR LED+	2	HDD LED+
3	PWR LED+	4	HDD LED-
5	PWR LED-	6	PW_BN+
7	SPEAKER+	8	PW_BN-
9	NC	10	RESET+
11	NC	12	RESET-
13	SPEAKER-	14	SLP_LED+
15	NC	16	SLP_LED-

216

115

CLE266

Power Switch (PW_BN) Connect to a 2-pin push button switch. Pressing this button will turn the system power on or off.

Reset Switch (RESET)

The Reset Switch is used to reboot the system rather than turning the power ON/OFF. Avoid rebooting while the HDD is working. You can connect the Reset Switch from the system case to this pin.

Power LED (PWR LED)

The LED is lit when the system is power on. If the system is in S1 (POS - Power On Suspend) or S3 (STR - Suspend To RAM) state, the LED will blink.

HDD LED

HDD LED shows the activity of a hard disk drive. Avoid turning the power off while HDD LED is lit. Connect the HDD LED from the system case to this pin.

SLP_LED

The SLP_LED is lit when the system is in the S1 (POS - Power On Suspend) state.

Speaker

The speaker from the system case is connected to this pin

2-12

Image 27

Contents User’s Manual Copyright TrademarksDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Onboard I/O Connectors Back Panel I/O PortsForm Factor Back Panel Mainboard LayoutAdd-On Module Placement of Add-On ModuleSlots Back Panel PortsConnecter/Jumper Description Onboard Connectors and JumpersChapter Installation VIA C3TM E-Series Processor CPUVIA Eden Processor DDR Sdram Module Installation Procedures Memory Module InstallationAvailable DDR Sdram Configurations ATX 20-Pin Power Connector Connecting the Power SupplyKeyboard Port PS2KB Mouse Port PS2MSVideo Port VGA OutUSB Ports RJ45 10/100 NIC PortIeee 1394 Port Serial Port COM1Card Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone IDE2 Secondary IDE Connector ConnectorsHard Disk Connectors IDE1 & IDE2 IDE1 Primary IDE ConnectorCase Connector Fpanel Power LED PWR LEDSpeaker Consumer Infrared Module / PS2 Header Kbms IrDA Infrared Module Connector FIRWake-on LAN WOL USB pin-header USB3/4COM2 The Second Serial Port Floppy Disk Drive Connector FDDFront Audio Panel Faudio CD Audio Connector CdinLPT Pin Header LPT SMBus Connector SMBusLvds Connector Optional Port ConnectorJumpers Clear Cmos ClearcmosRCA Video or S/PDIF Select Spdifsel PCI Interrupt Request Routing Peripheral Component Interconnect PCIBios Setup Control Keys Entering SetupGeneral Help F1 Getting HelpMain Menu Sub-MenuMain Menu Set User Password Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor PasswordDrive A/B Standard Cmos FeaturesDate TimeIDE Primary Master/Slave, Secondary Master/Slave CPU L2 Cache ECC Checking Advanced Bios FeaturesQuick Power On Self Test Virus WarningSwap Floppy Drive First/Second/Third Boot DeviceBoot Other Device Boot Up Floppy SeekTypematic Rate Chars/Sec Boot Up NumLock StatusTypematic Rate Setting Typematic Delay MsecDisplay Small Logo Show Summary InformationAdvanced Chipset Features AGP Mode InternalAGP Aperture Size Select Display Device CPU Direct Access FBAGP Fast Write CPU to PCI Post WriteDisplay Card Priority IDE Prefetch ModeIntegrated Peripherals Onboard IDE Channel 1/2OnChip USB Controller Onboard Lan Boot ROMAC97 Audio VIA OnChip LANOnboard Serial Port 1/2 Parallel Port ModeSuperIO Device Onboard FDC ControllerFast IR IRQ EPP Mode SelectECP Mode Use DMA Onboard Fast IRPower Management Setup HDD Power DownAcpi Suspend Type Video Off Option Power Management TimerPower Off by Pwrbtn Run Vgabios if S3 ResumePeripheral Activities PS2MS Wakeup from S3/S4/S5 PowerOn by PCI CardWake On LAN/Ring Connector RTC Alarm ResumePrimary Intr IRQs ActivitiesResource Controlled By PNP/PCI ConfigurationsPNP OS Installed Reset Configuration DataAssign IRQ For VGA/USB IRQ Resources PC Health Status Dram CAS Latency Frequency / Voltage ControlDram Clock Dram TimingActive to Precharge Tras Dram Command RateBank Interleave Precharge to Active TrpDram Voltage CPU ClockSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Driver Utilities Getting StartedRunning the Driver Utilities CD CD Content Chapter