Philips EPIA-MII user manual IDE Primary Master/Slave, Secondary Master/Slave

Page 42

BIOS Setup

IDE Primary Master/Slave, Secondary Master/Slave

Press Enter to enter the sub-menu and the following screen appears:

The specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. Select Auto whenever possible. If you select Manual, make sure the

information provided is from your hard disk vendor or system manufacturer.

IDE <Primary	The name of this menu item will match the
Master>	name of the menu. The settings are None,
	Auto, Manual.
Access Mode	The settings are CHS, LBA, Large, Auto.
Capacity	The formatted size of the storage device.
Cylinder	Number of cylinders.
Head	Number of heads.
Precomp	Write precompensation.
Landing Zone	Cylinder location of the landing zone.
Sector	Number of sectors.
PIO Mode	The settings are Mode 0/1/2/3/4, Auto.
Ultra DMA Mode	The settings are Disabled and Auto.

3-7

Image 42

Contents User’s Manual Copyright TrademarksDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Onboard I/O Connectors Back Panel I/O PortsForm Factor Mainboard Layout Back PanelPlacement of Add-On Module Add-On ModuleBack Panel Ports SlotsOnboard Connectors and Jumpers Connecter/Jumper DescriptionChapter Installation CPU VIA C3TM E-Series ProcessorVIA Eden Processor Memory Module Installation DDR Sdram Module Installation ProceduresAvailable DDR Sdram Configurations Connecting the Power Supply ATX 20-Pin Power ConnectorMouse Port PS2MS Keyboard Port PS2KBRJ45 10/100 NIC Port VGA OutUSB Ports Video PortIeee 1394 Port Serial Port COM1Card Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone IDE1 Primary IDE Connector ConnectorsHard Disk Connectors IDE1 & IDE2 IDE2 Secondary IDE ConnectorCase Connector Fpanel Power LED PWR LEDSpeaker IrDA Infrared Module Connector FIR Consumer Infrared Module / PS2 Header KbmsUSB pin-header USB3/4 Wake-on LAN WOLFloppy Disk Drive Connector FDD COM2 The Second Serial PortCD Audio Connector Cdin Front Audio Panel FaudioSMBus Connector SMBus LPT Pin Header LPTPort Connector Lvds Connector OptionalJumpers Clear Cmos ClearcmosRCA Video or S/PDIF Select Spdifsel Peripheral Component Interconnect PCI PCI Interrupt Request RoutingBios Setup Entering Setup Control KeysSub-Menu Getting HelpMain Menu General Help F1Main Menu Set Supervisor Password Load Fail-Safe DefaultsLoad Optimized Defaults Set User PasswordTime Standard Cmos FeaturesDate Drive A/BIDE Primary Master/Slave, Secondary Master/Slave Virus Warning Advanced Bios FeaturesQuick Power On Self Test CPU L2 Cache ECC CheckingBoot Up Floppy Seek First/Second/Third Boot DeviceBoot Other Device Swap Floppy DriveTypematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting Typematic Rate Chars/SecShow Summary Information Display Small LogoAdvanced Chipset Features AGP Mode InternalAGP Aperture Size CPU to PCI Post Write CPU Direct Access FBAGP Fast Write Select Display DeviceOnboard IDE Channel 1/2 IDE Prefetch ModeIntegrated Peripherals Display Card PriorityVIA OnChip LAN Onboard Lan Boot ROMAC97 Audio OnChip USB ControllerOnboard FDC Controller Parallel Port ModeSuperIO Device Onboard Serial Port 1/2Onboard Fast IR EPP Mode SelectECP Mode Use DMA Fast IR IRQPower Management Setup HDD Power DownAcpi Suspend Type Run Vgabios if S3 Resume Power Management TimerPower Off by Pwrbtn Video Off OptionPeripheral Activities RTC Alarm Resume PowerOn by PCI CardWake On LAN/Ring Connector PS2MS Wakeup from S3/S4/S5IRQs Activities Primary IntrReset Configuration Data PNP/PCI ConfigurationsPNP OS Installed Resource Controlled ByAssign IRQ For VGA/USB IRQ Resources PC Health Status Dram Timing Frequency / Voltage ControlDram Clock Dram CAS LatencyPrecharge to Active Trp Dram Command RateBank Interleave Active to Precharge TrasDram Voltage CPU ClockSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Driver Utilities Getting StartedRunning the Driver Utilities CD CD Content Chapter