Philips EPIA-MII EPP Mode Select, ECP Mode Use DMA, Onboard Fast IR, Fast IR IRQ, Fast IR DMA

Page 52

BIOS Setup

EPP Mode Select

EPP (Enhanced Parallel Port) comes in two modes: 1.9 and 1.7. EPP 1.9 is the newer version of the protocol and is backwards compatible with most EPP devices. If your EPP device does not work with the EPP 1.9 setting, try changing the setting to EPP 1.7.

Settings: EPP 1.9, EPP 1.7

ECP Mode Use DMA

ECP (Extended Capabilities Port) has two DMA channels that it can use. The default channel is 3. However, some expansion cards may use channel 3 as well. To solve this conflict, change the ECP channel to 1. Select a DMA channel for the port. Settings: 1, 3

Onboard Fast IR

Enables or disables the infrared port. Settings: Enabled and Disabled

Fast IR IRQ

Set this field to reserve an IRQ for the Fast IR port. This field is only available if Onboard Fast IR is enabled. Settings: 3, 4, 5, 11

Fast IR DMA

Set this field to choose the DMA channel. This field is only available if Onboard Fast IR is enabled. Settings: 6, 5

3-17

Image 52

Contents User’s Manual Trademarks CopyrightDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Back Panel I/O Ports Onboard I/O ConnectorsForm Factor Mainboard Layout Back PanelPlacement of Add-On Module Add-On ModuleBack Panel Ports SlotsOnboard Connectors and Jumpers Connecter/Jumper DescriptionChapter Installation CPU VIA C3TM E-Series ProcessorVIA Eden Processor Memory Module Installation DDR Sdram Module Installation ProceduresAvailable DDR Sdram Configurations Connecting the Power Supply ATX 20-Pin Power ConnectorMouse Port PS2MS Keyboard Port PS2KBVGA Out USB PortsRJ45 10/100 NIC Port Video PortSerial Port COM1 Ieee 1394 PortCard Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone Connectors Hard Disk Connectors IDE1 & IDE2IDE1 Primary IDE Connector IDE2 Secondary IDE ConnectorPower LED PWR LED Case Connector FpanelSpeaker IrDA Infrared Module Connector FIR Consumer Infrared Module / PS2 Header KbmsUSB pin-header USB3/4 Wake-on LAN WOLFloppy Disk Drive Connector FDD COM2 The Second Serial PortCD Audio Connector Cdin Front Audio Panel FaudioSMBus Connector SMBus LPT Pin Header LPTPort Connector Lvds Connector OptionalClear Cmos Clearcmos JumpersRCA Video or S/PDIF Select Spdifsel Peripheral Component Interconnect PCI PCI Interrupt Request RoutingBios Setup Entering Setup Control KeysGetting Help Main MenuSub-Menu General Help F1Main Menu Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor Password Set User PasswordStandard Cmos Features DateTime Drive A/BIDE Primary Master/Slave, Secondary Master/Slave Advanced Bios Features Quick Power On Self TestVirus Warning CPU L2 Cache ECC CheckingFirst/Second/Third Boot Device Boot Other DeviceBoot Up Floppy Seek Swap Floppy DriveBoot Up NumLock Status Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecShow Summary Information Display Small LogoAGP Mode Internal Advanced Chipset FeaturesAGP Aperture Size CPU Direct Access FB AGP Fast WriteCPU to PCI Post Write Select Display DeviceIDE Prefetch Mode Integrated PeripheralsOnboard IDE Channel 1/2 Display Card PriorityOnboard Lan Boot ROM AC97 AudioVIA OnChip LAN OnChip USB ControllerParallel Port Mode SuperIO DeviceOnboard FDC Controller Onboard Serial Port 1/2EPP Mode Select ECP Mode Use DMAOnboard Fast IR Fast IR IRQHDD Power Down Power Management SetupAcpi Suspend Type Power Management Timer Power Off by PwrbtnRun Vgabios if S3 Resume Video Off OptionPeripheral Activities PowerOn by PCI Card Wake On LAN/Ring ConnectorRTC Alarm Resume PS2MS Wakeup from S3/S4/S5IRQs Activities Primary IntrPNP/PCI Configurations PNP OS InstalledReset Configuration Data Resource Controlled ByAssign IRQ For VGA/USB IRQ Resources PC Health Status Frequency / Voltage Control Dram ClockDram Timing Dram CAS LatencyDram Command Rate Bank InterleavePrecharge to Active Trp Active to Precharge TrasCPU Clock Dram VoltageSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Getting Started Driver UtilitiesRunning the Driver Utilities CD CD Content Chapter