Philips EPIA-MII user manual SuperIO Device, Onboard FDC Controller, Onboard Serial Port 1/2

Page 51

Chapter 3

SuperIO Device

Press Enter to enter the sub-menu and the following screen appears:

Onboard FDC Controller

Enable the onboard floppy controller. Select Enabled when you have installed a floppy disk drive. Settings: Enabled, Disabled

Onboard Serial Port 1/2

Set the base I/O port address and IRQ for the onboard serial port A/serial port B. Selecting Auto allows BIOS to automatically determine the correct base I/O port address. Settings:

Port	Settings
1	Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Auto

2Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Auto

Onboard Parallel Port

This specifies the I/O port address and IRQ of the onboard parallel port.

Settings: Disabled, 378/IRQ7, 278/IRQ5, 3BC/IRQ7

Parallel Port Mode

Set the parallel port mode. To operate the onboard parallel port as Standard Parallel Port, choose SPP. To operate the onboard parallel port in the EPP mode, choose EPP. By choosing ECP, the onboard parallel port will operate in ECP mode. Choosing ECP + EPP will allow the onboard parallel port to support both the ECP and EPP modes simultaneously.

Settings: SPP, EPP, ECP, ECP + EPP

3-16

Image 51

Contents User’s Manual Copyright TrademarksDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Onboard I/O Connectors Back Panel I/O PortsForm Factor Back Panel Mainboard LayoutAdd-On Module Placement of Add-On ModuleSlots Back Panel PortsConnecter/Jumper Description Onboard Connectors and JumpersChapter Installation VIA C3TM E-Series Processor CPUVIA Eden Processor DDR Sdram Module Installation Procedures Memory Module InstallationAvailable DDR Sdram Configurations ATX 20-Pin Power Connector Connecting the Power SupplyKeyboard Port PS2KB Mouse Port PS2MSVideo Port VGA OutUSB Ports RJ45 10/100 NIC PortIeee 1394 Port Serial Port COM1Card Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone IDE2 Secondary IDE Connector ConnectorsHard Disk Connectors IDE1 & IDE2 IDE1 Primary IDE ConnectorCase Connector Fpanel Power LED PWR LEDSpeaker Consumer Infrared Module / PS2 Header Kbms IrDA Infrared Module Connector FIRWake-on LAN WOL USB pin-header USB3/4COM2 The Second Serial Port Floppy Disk Drive Connector FDDFront Audio Panel Faudio CD Audio Connector CdinLPT Pin Header LPT SMBus Connector SMBusLvds Connector Optional Port ConnectorJumpers Clear Cmos ClearcmosRCA Video or S/PDIF Select Spdifsel PCI Interrupt Request Routing Peripheral Component Interconnect PCIBios Setup Control Keys Entering SetupGeneral Help F1 Getting HelpMain Menu Sub-MenuMain Menu Set User Password Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor PasswordDrive A/B Standard Cmos FeaturesDate TimeIDE Primary Master/Slave, Secondary Master/Slave CPU L2 Cache ECC Checking Advanced Bios FeaturesQuick Power On Self Test Virus WarningSwap Floppy Drive First/Second/Third Boot DeviceBoot Other Device Boot Up Floppy SeekTypematic Rate Chars/Sec Boot Up NumLock StatusTypematic Rate Setting Typematic Delay MsecDisplay Small Logo Show Summary InformationAdvanced Chipset Features AGP Mode InternalAGP Aperture Size Select Display Device CPU Direct Access FBAGP Fast Write CPU to PCI Post WriteDisplay Card Priority IDE Prefetch ModeIntegrated Peripherals Onboard IDE Channel 1/2OnChip USB Controller Onboard Lan Boot ROMAC97 Audio VIA OnChip LANOnboard Serial Port 1/2 Parallel Port ModeSuperIO Device Onboard FDC ControllerFast IR IRQ EPP Mode SelectECP Mode Use DMA Onboard Fast IRPower Management Setup HDD Power DownAcpi Suspend Type Video Off Option Power Management TimerPower Off by Pwrbtn Run Vgabios if S3 ResumePeripheral Activities PS2MS Wakeup from S3/S4/S5 PowerOn by PCI CardWake On LAN/Ring Connector RTC Alarm ResumePrimary Intr IRQs ActivitiesResource Controlled By PNP/PCI ConfigurationsPNP OS Installed Reset Configuration DataAssign IRQ For VGA/USB IRQ Resources PC Health Status Dram CAS Latency Frequency / Voltage ControlDram Clock Dram TimingActive to Precharge Tras Dram Command RateBank Interleave Precharge to Active TrpDram Voltage CPU ClockSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Driver Utilities Getting StartedRunning the Driver Utilities CD CD Content Chapter