Philips EPIA-MII user manual First/Second/Third Boot Device, Boot Other Device, Swap Floppy Drive

Page 44

BIOS Setup

First/Second/Third Boot Device

Set the boot device sequence as BIOS attempts to load the disk operating system. The settings are:

Floppy	The system will boot from floppy drive.
LS120	The system will boot from LS-120 drive.
HDD-0	The system will boot from first HDD.
SCSI	The system will boot from SCSI.
CD-ROM	The system will boot from CD-ROM.
HDD-1	The system will boot from second HDD.
HDD-2	The system will boot from third HDD.
HDD-3	The system will boot from fourth HDD.
ZIP100	The system will boot from ATAPI ZIP drive.
USB-FDD	The system will boot from USB floppy drive.
USB-ZIP	The system will boot from USB ZIP drive.
USB-CDROM	The system will boot from USB CDROM.
USB-HDD	The system will boot from USB HDD.
LAN	The system will boot from network drive.
Disabled	Disable this sequence.

Boot Other Device

Enable the system to boot from other devices if the system fails to boot from the First/Second/Third boot device. Settings: Enabled and Disabled

Swap Floppy Drive

If the system has two floppy drives, choose Enabled to assign physical drive B to logical drive A and vice versa. Settings: Enabled and Disabled

Boot Up Floppy Seek

Set floppy seek during POST, BIOS will determine whether the floppy is 40 or 80 tracks. Settings: Enabled and Disabled

3-9

Image 44

Contents User’s Manual Disclaimer CopyrightTrademarks FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Form Factor Onboard I/O ConnectorsBack Panel I/O Ports Mainboard Layout Back PanelPlacement of Add-On Module Add-On ModuleBack Panel Ports SlotsOnboard Connectors and Jumpers Connecter/Jumper DescriptionChapter Installation CPU VIA C3TM E-Series ProcessorVIA Eden Processor Memory Module Installation DDR Sdram Module Installation ProceduresAvailable DDR Sdram Configurations Connecting the Power Supply ATX 20-Pin Power ConnectorMouse Port PS2MS Keyboard Port PS2KBVGA Out USB PortsRJ45 10/100 NIC Port Video PortCard Slots PCMCIA, CF Ieee 1394 PortSerial Port COM1 Audio Jacks Line-In, Line-Out, Microphone Connectors Hard Disk Connectors IDE1 & IDE2IDE1 Primary IDE Connector IDE2 Secondary IDE ConnectorSpeaker Case Connector FpanelPower LED PWR LED IrDA Infrared Module Connector FIR Consumer Infrared Module / PS2 Header KbmsUSB pin-header USB3/4 Wake-on LAN WOLFloppy Disk Drive Connector FDD COM2 The Second Serial PortCD Audio Connector Cdin Front Audio Panel FaudioSMBus Connector SMBus LPT Pin Header LPTPort Connector Lvds Connector OptionalRCA Video or S/PDIF Select Spdifsel JumpersClear Cmos Clearcmos Peripheral Component Interconnect PCI PCI Interrupt Request RoutingBios Setup Entering Setup Control KeysGetting Help Main MenuSub-Menu General Help F1Main Menu Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor Password Set User PasswordStandard Cmos Features DateTime Drive A/BIDE Primary Master/Slave, Secondary Master/Slave Advanced Bios Features Quick Power On Self TestVirus Warning CPU L2 Cache ECC CheckingFirst/Second/Third Boot Device Boot Other DeviceBoot Up Floppy Seek Swap Floppy DriveBoot Up NumLock Status Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecShow Summary Information Display Small LogoAGP Aperture Size Advanced Chipset FeaturesAGP Mode Internal CPU Direct Access FB AGP Fast WriteCPU to PCI Post Write Select Display DeviceIDE Prefetch Mode Integrated PeripheralsOnboard IDE Channel 1/2 Display Card PriorityOnboard Lan Boot ROM AC97 AudioVIA OnChip LAN OnChip USB ControllerParallel Port Mode SuperIO DeviceOnboard FDC Controller Onboard Serial Port 1/2EPP Mode Select ECP Mode Use DMAOnboard Fast IR Fast IR IRQAcpi Suspend Type Power Management SetupHDD Power Down Power Management Timer Power Off by PwrbtnRun Vgabios if S3 Resume Video Off OptionPeripheral Activities PowerOn by PCI Card Wake On LAN/Ring ConnectorRTC Alarm Resume PS2MS Wakeup from S3/S4/S5IRQs Activities Primary IntrPNP/PCI Configurations PNP OS InstalledReset Configuration Data Resource Controlled ByAssign IRQ For VGA/USB IRQ Resources PC Health Status Frequency / Voltage Control Dram ClockDram Timing Dram CAS LatencyDram Command Rate Bank InterleavePrecharge to Active Trp Active to Precharge TrasSpread Spectrum Dram VoltageCPU Clock Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Running the Driver Utilities CD Driver UtilitiesGetting Started CD Content Chapter