Philips EPIA-MII user manual Memory Module Installation, DDR Sdram Module Installation Procedures

Page 19

Chapter 2

Memory Module Installation

The VIA EPIA-MII Mini-ITX Mainboard provides one DIMM slot for DDR266 SDRAM memory modules.

CLE266

DDR SDRAM Module Installation Procedures

1.Push the white retaining latches at either end of the DIMM slot outwards.

2.Align the DDR SDRAM module with the corresponding notches on the DIMM slot. The modules will only fit if placed in the correct position.

3.With both hands, press the DDR SDRAM module down into the DIMM slot so that the white retaining latches rotate up and secure the module in place (see picture below).

2-4

Image 19

Contents User’s Manual Trademarks CopyrightDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Back Panel I/O Ports Onboard I/O ConnectorsForm Factor Back Panel Mainboard LayoutAdd-On Module Placement of Add-On ModuleSlots Back Panel PortsConnecter/Jumper Description Onboard Connectors and JumpersChapter Installation VIA C3TM E-Series Processor CPUVIA Eden Processor DDR Sdram Module Installation Procedures Memory Module InstallationAvailable DDR Sdram Configurations ATX 20-Pin Power Connector Connecting the Power SupplyKeyboard Port PS2KB Mouse Port PS2MSVideo Port VGA OutUSB Ports RJ45 10/100 NIC PortSerial Port COM1 Ieee 1394 PortCard Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone IDE2 Secondary IDE Connector ConnectorsHard Disk Connectors IDE1 & IDE2 IDE1 Primary IDE ConnectorPower LED PWR LED Case Connector FpanelSpeaker Consumer Infrared Module / PS2 Header Kbms IrDA Infrared Module Connector FIRWake-on LAN WOL USB pin-header USB3/4COM2 The Second Serial Port Floppy Disk Drive Connector FDDFront Audio Panel Faudio CD Audio Connector CdinLPT Pin Header LPT SMBus Connector SMBusLvds Connector Optional Port ConnectorClear Cmos Clearcmos JumpersRCA Video or S/PDIF Select Spdifsel PCI Interrupt Request Routing Peripheral Component Interconnect PCIBios Setup Control Keys Entering SetupGeneral Help F1 Getting HelpMain Menu Sub-MenuMain Menu Set User Password Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor PasswordDrive A/B Standard Cmos FeaturesDate TimeIDE Primary Master/Slave, Secondary Master/Slave CPU L2 Cache ECC Checking Advanced Bios FeaturesQuick Power On Self Test Virus WarningSwap Floppy Drive First/Second/Third Boot DeviceBoot Other Device Boot Up Floppy SeekTypematic Rate Chars/Sec Boot Up NumLock StatusTypematic Rate Setting Typematic Delay MsecDisplay Small Logo Show Summary InformationAGP Mode Internal Advanced Chipset FeaturesAGP Aperture Size Select Display Device CPU Direct Access FBAGP Fast Write CPU to PCI Post WriteDisplay Card Priority IDE Prefetch ModeIntegrated Peripherals Onboard IDE Channel 1/2OnChip USB Controller Onboard Lan Boot ROMAC97 Audio VIA OnChip LANOnboard Serial Port 1/2 Parallel Port ModeSuperIO Device Onboard FDC ControllerFast IR IRQ EPP Mode SelectECP Mode Use DMA Onboard Fast IRHDD Power Down Power Management SetupAcpi Suspend Type Video Off Option Power Management TimerPower Off by Pwrbtn Run Vgabios if S3 ResumePeripheral Activities PS2MS Wakeup from S3/S4/S5 PowerOn by PCI CardWake On LAN/Ring Connector RTC Alarm ResumePrimary Intr IRQs ActivitiesResource Controlled By PNP/PCI ConfigurationsPNP OS Installed Reset Configuration DataAssign IRQ For VGA/USB IRQ Resources PC Health Status Dram CAS Latency Frequency / Voltage ControlDram Clock Dram TimingActive to Precharge Tras Dram Command RateBank Interleave Precharge to Active TrpCPU Clock Dram VoltageSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Getting Started Driver UtilitiesRunning the Driver Utilities CD CD Content Chapter