IBM SC41-5420-04 Work with TCP/IP Connection Status, Route Type Opt Destination Service, Bottom

Page 52

Display TCP/IP Route Information

 

 

 

 

System: SYSNAM04

Type options, press Enter.

 

 

 

5=Display details

 

 

 

 

Route

Type of

Route

Route

Route

Opt Destination

Service

MTU

Type

Source

9.125.87.0

*MAXTHRPUT

1989

*DIRECT

*CFG

9.125.87.0

*NORMAL

1989

*DIRECT

*CFG

9.125.109.3

*MINDELAY

576

*HOST

*ICMP

127.0.0.0

*NORMAL

576

*DIRECT

*CFG

*DFTROUTE

*MAXTHRPUT

1989

*DFTROUTE

*CFG

*DFTROUTE

*NORMAL

1989

*DFTROUTE

*CFG

Bottom

F3=Exit

F5=Refresh

F6=Print list

F11=Display next hop

F12=Cancel

F13=Sort by column

F17=Top

F18=Bottom

 

Figure 28. Display TCP/IP Route Information, Display 2 of 2

To view detailed information about a specific route, type 5 in the option field next to the route and press the Enter key.

Routes listed on the Display TCP/IP Route Information display differ from the routes that are displayed on the Work with TCP/IP Routes display. Only routes with a route source of *CFG and a route type that is not *DIRECT can be changed with the Work with TCP/IP Routes display. Similarly, only routes that meet these conditions can be changed or removed with the CHGTCPRTE or RMVTCPRTE commands. *CFG means the route was added using iSeries configuration commands or is a *DIRECT route. *DIRECT means that the route is to a network or subnetwork to which this system has a direct physical connection. This route is not defined with an add route command.

Work with TCP/IP Connection Status

The Work with TCP/IP Connection Status display allows you to display or end a TCP/IP connection between a local system and a remote system.

To display the Work with TCP/IP Connection Status display:

1.Type 3 on the command line of the Work with TCP/IP Network Status menu or enter the WRKTCPSTS *CNN command.

2.Press the Enter key.

The first of the three Work with TCP/IP Connection Status displays, as shown in Figure 29 on page 39.

To display the second and third Work with TCP/IP Connection Status displays, press F11 (see Figure 30 on page 39 and Figure 31 on page 40). To display port numbers instead of port service names, press F14.

In Figure 29 on page 39, the connections indicate that the FTP server, SMTP server, and TELNET server are active and ready to receive connection attempts. Because no connection has been established yet, the Remote Address and Remote Port fields

38OS/400 TCP/IP Configuration and Reference V5R1

Image 52
Contents TCP/IP Configuration and Reference Page TCP/IP Configuration and Reference Fifth Edition May Contents Index About TCP/IP Configuration and Reference SC41-5420 Vi OS/400 TCP/IP Configuration and Reference V5R1 Prerequisite and related information Operations NavigatorViii OS/400 TCP/IP Configuration and Reference V5R1 Page OS/400 TCP/IP Configuration and Reference V5R1 Summary of changes Xii OS/400 TCP/IP Configuration and Reference V5R1 Configuring TCP/IP What you need to know before you can configure TCP/IPPlanning for TCP/IP Installation and Configuration Gathering Information About your NetworkTCP/IP Planning Checklists Line Description Parameters ChecklistLocal TCP/IP Host Information Checklist Interfaces to Local TCP/IP NetworksInstalling the TCP/IP Application Programs 25 / Remote System InformationUsing the TCP/IP Administration Menu TcpadmUsing the Configure TCP/IP Menu Configure TCP/IP Menu CfgtcpConfiguring TCP/IP using the EZ-Setup Wizard Configuring TCP/IP using the Command Line InterfaceServices table Protocol tableConfiguring a Line Description Configuring a TCP/IP InterfaceImportant Note Internet addressSubnet mask Line descriptionAssociated local interface Automatic startConfiguring TCP/IP Routes Do you need to add routes at all?Route destination Maximum Transmission Unit MTU sizeAdding TCP/IP routes Preferred binding interfaceDftroute None Normal Multiple Default RoutesNO, *YES Configuring TCP/IP attributes Configuring TCP/IP Remote System InformationIP Datagram Forwarding Adding Remote System InformationNone NONE, *REQUEST, *ACCEPT PVCLind 15, *LIND, *TRANSMIT Configuring TCP/IP Host Table Entries Adding an Entry to the Host TableWork with TCP/IP Host Table Display Macian BernDNS Loopback SYSNAM890Localhost Configuring the Local Domain and Host Name AnyNet/400 Appc over TCP/IPDomain Name System DNS Server LocalStarting TCP/IP and TCP/IP Servers Dspmsg Qsysopr Dspmsg QtcpTCP/IP Jobs Job Name DescriptionVerifying the TCP/IP Connection End TCP/IP EndtcpVerifying Additional TCP/IP Connections Successful Ping MessagesVerify TCP/IP Connection Verify TCP/IP Connection VfytcpcnnVerifying TCP/IP Connections with Host Name-Example Verify TCP/IP Connection PingVERBOSE, *QUIET COMP, *ESCAPESaving Your TCP/IP Configuration Verifying TCP/IP Connections with Internet Address-ExampleConfiguring TCP/IP 32 OS/400 TCP/IP Configuration and Reference V5R1 Network Status Work with TCP/IP Network Status MenuWork with TCP/IP Interface Status Work with TCP/IP Network StatusWork with TCP/IP Interface Status Internet Network LineOpt Address Mask Service Starting TCP/IP InterfacesInternet Subnet Type MaxthrputEnding TCP/IP Interfaces Display TCP/IP Route Information Display TCP/IP Route InformationRoute Subnet Next Opt Destination Mask Hop Available Route Type Opt Destination Service Work with TCP/IP Connection StatusType Source BottomRemote Local Opt Address Port Idle Time State Work with TCP/IP Connection StatusRemote Local Opt Address Port User Bytes Out Ending TCP/IP Connections ALLRemote Local Opt Address Port Type TCPWorking with Configuration Status Confirm End of TCP/IP ConnectionsDisplaying TCP/IP Network Status Information Display Multicast GroupsOpt Description Status Job Trnline Active Trnlinet Trnlitcp QtcpipDisplay Multicast Host Groups Displaying TCP/IP InterfacesHost Group Hardware Address Displaying Associated Routes Display TCP/IP Interface StatusTrlan MSBDisplay Associated Routes Displaying Route Details OptionRoute Subnet Next Opt Destination Mask Hop Display TCP/IP Route Details Displaying TCP/IP Route InformationDirect Display TCP/IP Route Information, Display 1 Displaying TCP/IP Connections Display TCP Connection StatusDisplaying Connection Totals Display TCP/IP Connection Status, Display 2TCP/IP Host Tables Display TCP/IP Connection TotalsManaging TCP/IP Host Tables Host File FormatsHost Table Information with *AIX Files Host Table Information with *NIC FilesMerging TCP/IP Host Tables Tips for Merging Host TablesHost Table Information with *AS400 Files Managing the Host Table from a Central Site Merge the File Negative Advice from TCP or the Data Link Layer Dead Gateway ProcessingHow IP Responds to Negative Advice Multihoming FunctionMultihoming Single Host, Single Network, Single Line Per physical LAN only Example The Multihoming function Multihoming TCP/IP NetworkX25LINE Type of Service TOSLoopback None Multiple Routes TOS ExampleTCP/IP Port Restriction Configuring TCP/IP Port Restrictions PaoloOnly UDP, *TCPGerry Configure Related Tables Menu Related Tables and the Host TableWork with Service Table Entry Display Using X.25 PVC instead of SVC IBMMulticast Restrictions Chglintrn Lindtrnline FCNADRC00000040000 70 OS/400 TCP/IP Configuration and Reference V5R1 TCP/IP Jobs Base Pool SizeTCP/IP Protocol Support Provided by IOP Outbound batching of TCP and UDP datagrams Merge Host Table Performance Running TCP/IP Only Performance Considerations74 OS/400 TCP/IP Configuration and Reference V5R1 Line type Configuration command Configuration Steps Source Service Access PointCreating the Line Description Line Description NameSetting the Maximum Transmission Unit Determining the Maximum Size of Datagrams78 OS/400 TCP/IP Configuration and Reference V5R1 Appendix B. TCP/IP Application Exit Points and Programs TCP/IP Exit Points and Exit ProgramsOS/400 Registration Facility TCP/IP Application Exit PointsCreating Exit Programs Adding Your Exit Program to the Registration FacilitySelect your exit point QAPP0100Select the Add Exit Program option Add your exit programRemoving Exit Programs YourlibExit Point Interfaces for TCP/IP Application Exit Points TCP/IP Application Request Validation Exit Point InterfaceRequired Parameter Group Application identifierOperation identifier User profileRemote IP address Length of remote IP addressLength of operation-specific information Usage NotesAllow operation QSYS.LIB file system pathnames are always in uppercase Length of command string Command stringPoint Command processor identifier Character conversion optionQshell interpreter not installed 92 OS/400 TCP/IP Configuration and Reference V5R1 Copyright IBM Corp Programming Interface Information TrademarksDB2 96 OS/400 TCP/IP Configuration and Reference V5R1 Index Special Characters Interface Qtgtelnets Qtsmtpsrvr Page SC41-5420-04