IBM 8677 manual Installing options

Page 33

Statement 8:

CAUTION:

Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.

Complete the following steps to install a module:

Note: These instructions assume the BladeCenter unit is connected to power.

1.Read the safety information beginning on page vii and “Installation guidelines” on page 13 through “Handling static-sensitive devices” on page 14.

2.Remove the acoustic module option, if installed, from the rear of the BladeCenter unit. See “Installing and removing the acoustic module option” on page 21 for instructions.

3.Remove the filler module from the bay.

4.Ensure that the release lever on the module is in the open position (perpendicular to the module).

5.Slide the module into the appropriate module bay until it stops.

6.Push the release lever on the front of the module closed.

7.Attach any cables or cords required by the module. See “Input/output connectors” on page 26 for the location of connectors on the BladeCenter unit. Be sure to route the power cord on a power module through the strain-relief clamp on the power module.

8.Make sure the LEDs on the module indicate that it is operating properly. Verify that:

vThe dc power LED and the ac power LED on each power module are lit.

vThe OK LED on the management module is lit.

vThe OK LED on each I/O module is lit.

9.If you have other modules to install, do so now; otherwise, go to step 10.

10.Replace the acoustic module option, if you removed it in step 2.

Chapter 2. Installing options 19

Image 33
Contents Installation and User’s Guide Server Support ERserver Page Contents Configuring your BladeCenter unit Chapter Sharing resources among the blade serversAppendix A. Getting help and technical assistance Appendix C. Notices Vi BladeCenter Type 8677 Installation and User’s Guide Vii SafetyTo Connect To Disconnect Do not ≥ 18 kg 39.7 lb ≥ 32 kg 70.5 lb ≥ 55 kg 121.2 lb Safety Xii BladeCenter Type 8677 Installation and User’s Guide Introduction This Installation and User’s Guide provides information toFront About your documentation CD Using the IBM Documentation BrowserSystem requirements Starting the IBM Documentation BrowserRelated publications Using the search featureIntroduction Features and specifications Features and specificationsIBM Enterprise X-Architecture technology What your BladeCenter unit offersExpansion capabilities Hot-swap capabilitiesRedundant network connection capabilities Redundancy capabilitiesSystem-management capabilities Network environment supportReliability, availability, and serviceability CD-ROM Major components of the BladeCenter Type 8677 unitRear view Front viewBladeCenter Type 8677 Installation and User’s Guide Installing the BladeCenter unit in a rack Installing optionsInstallation guidelines Use safe practices when liftingHandling static-sensitive devices System reliability considerationsBladeCenter modules Installing and removing modulesModules Power modules Blower modules Installing a moduleInstalling options Removing a module Installing the acoustic module option Installing and removing the acoustic module optionRemoving the acoustic module option Installing and removing blade serversBlade server expansion options Installing a blade serverLabel Removing a blade server Input/output connectors Completing the installationKeyboard connector Video connectorMouse connector Remote management and console Ethernet connectorModule connectors Starting the BladeCenter unit BladeCenter unit power, controls, and indicatorsShutting down the BladeCenter unit BladeCenter components, controls, and LEDs Writeable area Rear system LED panel Module Ethernet activity System LED panel Configuring your BladeCenter unit Resolution Refresh rate Configuring the management module for remote access Setting up the remote connectionCabling the Ethernet port Ethernet link LEDCommunicating with the IBM Director software Verifying your Wake on LAN configuration Configuring Wake on LAN in the BladeCenter unitLinux-specific configuration Using the management and configuration programStarting the management and configuration program Configuring the external Ethernet port Management and configuration program optionsConfiguring the internal Ethernet port Saving and restoring the configuration fileUsing IBM Director About the wizardStarting the wizard Configuring a switch module Using Remote Deployment Manager Version 4.1 or laterSupporting Ethernet failover What to configureBladeCenter networking guidelines Configuring the Ethernet controllers in the blade serversGbps links L2 Switch Sharing resources among the blade servers BladeCenter Type 8677 Installation and User’s Guide Diagnostic tools overview Solving problemsMonitor problems Troubleshooting chartsPower problems Management module problemsBlower module problems Light path diagnostics feature Options problemsLit LED Cause Action BladeCenter system LED panel Light path diagnostics LEDsLit LED Cause Action Power module Before you call Appendix A. Getting help and technical assistanceSoftware service and support Hardware service and support What this Warranty Does not Cover What this Warranty CoversPart 1 General Terms Part 1 General TermsWhat IBM Will Do to Correct Problems How to Obtain Warranty ServiceExchange of a Machine or Part Your Additional ResponsibilitiesLimitation of Liability Part 2 Country-unique Terms Governing LawJurisdiction United States Hong Kong S.A.R. of China and Macau S.A.R. of China Malaysia Following Terms Apply to ALL Emea Countries Arbitration The following is added under this heading Following Terms Apply to ALL EU Countries Following paragraphs are added to this section Egypt Hungary Slovakia Items for Which IBM is Not LiableWarranty Period Part 3 Warranty InformationTypes of Warranty Service Customer Replaceable Unit CRU ServiceCourier or Depot Service On-site ServiceCustomer Carry-In or Mail-In Service EU Country Telephone ListEdition notice Appendix C. NoticesImportant notes TrademarksProduct recycling and disposal Battery return program Federal Communications Commission FCC statement Electronic emission noticesIndustry Canada Class a emission compliance statement European Union EMC Directive conformance statementAppendix C. Notices Macedonia former Yugoslav Republic of, Madagascar, Mali Appendix C. Notices BladeCenter Type 8677 Installation and User’s Guide Index RAS Index BladeCenter Type 8677 Installation and User’s Guide Page Part Number 59P6595