Star Micronics TSP2000 Series user manual EC Council Directive 89/336/EEC of 3 May

Page 2

Federal Communications Commission

Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

CE

Manufacturer’s Declaration of Conformity

EC Council Directive 89/336/EEC of 3 May 1989

This product, has been designed and manufactured in accordance with the International Standards EN 50081-1/01.92 and EN 50082-1/01.92, following the provisions of the Electro Magnetic Compatibility Directive of the European Communities as of May 1989.

EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993

This product, has been designed and manufactured in accordance with the International Standards EN 60950, following the provisions of the Low Voltage Directive of the European Communities as of July 1993.

The above statement applies only to printers marketed in EU.

Trademark acknowledgments

TSP2000: Star Micronics Co., Ltd.

ESC/POS: Seiko Epson Corporation

Notice

∙All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’s express permission is forbidden.

∙The contents of this manual are subject to change without notice.

∙All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to press. However, should any errors be detected, STAR would greatly appreciate being informed of them.

∙The above notwithstanding, STAR can assume no responsibility for any errors in this manual.

© Copyright 2000 Star Micronics Co., LTD.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents TSP2000 Series EC Council Directive 89/336/EEC of 3 May Table of Contents Appendix D Serial Interface Parts Identification and Nomenclature Choosing a place for the printer Consumable Parts and AC Adapter Connecting Cables and AC Adapter Interface Cable Ferrite Core InstallationConnecting the Interface Cable Connecting to a Peripheral Unit Cm maximum Fastener Pull and cut Connecting the Optional AC Adapter Turning Power On Error LED red LED Paper Feed SwitchPower LED green LED Control PanelLoading Paper Loading New Roll PaperPaper Removing Remaining Paper Near-end Sensor Diameter of remaining paper a Screw position Removing Paper Jam Preventing and Clearing Paper JamsPreventing Paper Jams Releasing a Locked Cutter Moving blade Check window Hexadecimal Dump Test Print MethodProducing a Test Print Cleaning the Paper Holder Periodical CleaningCleaning the Thermal Head Table DES Matieres Identification des pièces et nomenclature Emplacement de l’imprimante Consommables et adaptateur secteur Câble d’interface Installation du tore de ferrite Câbles de connexion et adaptateur secteurConnexion du câble d’interface Raccordement d’un appareil périphérique Cm maximum Attache Connexion de l’adaptateur secteur optionnel Mise sous tension de l’imprimante DEL d’erreur Error DEL rouge Panneau des commandesDEL d’alimentation Power DEL verte Touche d’avance de papier Paper FeedChargement du papier Chargement d’un rouleau de papier neufPapier Retrait du papier Capteur de fin de rouleau Diamètre du papier restant a Position de la vis Prévention des bourrages de papier Correction de bourrages de papierLibération d’une unité de découpage bloquée Unité de découpage automatique Couvercle avant Vidage hexadécimal Test d’impressionExécution d’un test d’impression Nettoyage du support de papier NettoyageNettoyage de la tête d’impression Français Inhaltsverzeichnis Beschreibung und Bezeichnung der Geräteteile Wahl eines Aufstellungsorts für den Drucker Verbrauchsteile und Netzteil Anschlußkabel und Netzteil Schnittstellenkabel Anbringen des FerritkernsAnschließen des Schnittstellenkabels Anschluß an ein Peripheriegerät Maximum 5 cm Kabelbinder Ziehen und Abschneiden Anschließen des optionalen Netzteils Einschalten Bedienfeld Netz-LED Power grüne LEDFehler-LED Error rote LED Papiereinzugknopf Paper FeedEinlegen von Papier Einlegen einer neuen PapierrollePapier Entfernen des restlichen Papiers Papiervorrat-Sensor Vorsichtsmaßregeln Beheben von Papierstau Verhindern und Beheben von PapierstauVerhindern von Papierstau Freigeben eines gesperrten Schneidmessers AchtungAutomatisches Schneidmesser Frontabdeckung Sedezimaler Datenausdruck Testdruck-VerfahrenErstellen eines Testdrucks Reinigen des Papierhalters Regelmäßige ReinigungReinigen des Thermalkopfes Deutsch Indice Identificazione delle parti e nomenclatura Scelta di un luogo per la stampante Parti soggette a consumo e trasformatore CA Cavo interfaccia Installazione dell’anello di ferrite Cavi di collegamento e trasformatore CACollegamento del cavo interfaccia Collegamento ad un’unità periferica Cm massimo Fascetta di fissaggio Collegamento del trasformatore CA opzionale Accensione Pannello di controllo Spia Power LED verdeSpia Error LED rosso Interruttore Paper FeedCaricamento della carta Caricamento di un nuovo rotolo di cartaCarta Rimozione della carta rimanente Sensore di rilevamento fine carta Attenzione Prevenzione degli inceppamenti della carta Eliminazione degli inceppamenti della cartaRilascio della taglierina bloccata CautelaTaglierina automatica Coperchio anteriore Scaricamento esadecimali Metodo per la stampa di provaProduzione di uno stampato di prova Pulizia del comparto carta Pulizia periodicaPulizia della testina termica Italiano Appendix a Specifications General SpecificationsPower Supply Print SpecificationsAuto Cutter Specifications InterfaceEnvironmental Requirements ReliabilityAppendix B Dip Switch Setting Serial Interface Type DIP-SWParallel Interface Type Table of Connection Signals for Each Mode Appendix C Parallel InterfaceDuring Reverse mode Function for Compatibility Mode IN/OUTRS-232C Connector Appendix D Serial InterfaceElectrical Characteristics Cable ConnectionsPeripheral Drive Connector Appendix E Periheral Unit Drive CircuitOverseas Subsidiary Companies Star Micronics AMERICA, INC
Top Page Image Contents