Star Micronics 347F user manual Control Panel, LED flashes Validation printing mode is set

Page 13

3.CONTROL PANEL

1 “ON LINE” switch

Switches the printer between “ON LINE” and “OFF LINE”. When- ever the printer switches between “ON LINE” and “OFF LINE”, the

buzzer gives one short beep (“ON LINE” and “OFF LINE” switching is possible only when the paper is loaded in the printer.)

2 “FEED” switch

∙ When this switch is pressed and then released within 0.5 sec., the paper feeds one line.

∙ When this switch is depressed for

Fig. 3-1 Control panelmore than 0.5 sec., the paper feeds continuously.

(The above paper feed operation is possible for both “ON LINE” and “OFF LINE” modes.)

3“POWER” lamp (green LED)

∙Lights when the power for the printer is on. 4 “ALARM” lamp (red LED)

∙Lights when the paper is out.

If the paper is out, load a new roll then press the “ON LINE” switch.

∙Flashes when the front cover is open or a mechanical error (motor lock etc.) occurs. The buzzer will give one short beep followed by a long beep. Mount the front cover properly and press the “ON LINE” switch. If the buzzer still sounds and the “ALARM” lamp flashes, this signifies that a mechanical error has occurred. Locate the cause of the error and turn the power for the printer off and back on again to reset the printer.

(In case of a mechanical error, the data will not be cleared even if the power is turned off.)

5“ON LINE” lamp (green LED) LED lit: Printer is ON LINE LED off: Printer is OFF LINE

LED flashes: Validation printing mode is set.

When all lamps 3to 5light simultaneously and the buzzer sounds continu- ously, a CPU error has occurred. In case of a CPU error, turn off the power then turn it on again. When turning off the power, the data will be cleared.

ENGLISH

– 11 –

Image 13

Contents SP317/347F EC Council Directive 89/336/EEC of 3 May Table of Contents Loading the Ribbon Cartridge Turn the power switch on the printer to the off positionTo remove the front cover lift it up To the off positionApprox cm. and pull it forward Immediately after printingInsert the ink ribbon between Tion until you hear a locking soundProtruding beyond the ribbon sepa RatorRemoving the rear cover SP317 Loading the PaperSetting of the paper guide SP317 Removing the rear cover SP347 Position of the adjust lever SP347 10 Loading the paper SP347 Removing the Roll Paper Control Panel LED flashes Validation printing mode is setPage Table DES Matières Installation D’UNE Cartouche DE Ruban Dépose du cache avant SP347 OK NON Montage des attaches pour Rouleau de papier SP317 Chargement DU PapierPositionnement des guides de Papier SP317 Avancer le papierPouces Vez-le d’environ 3 cm, puis tirez-le vers l’avantPositionnement du levier d’ajus 10 Chargement du papier SP347 Enlèvement d’un rouleau de papier Touche en ligne on Line Panneau DE CommandePage Inhaltsverzeichnis Einlegen DER Farbbandkassette Abb -3 Abnehmen der Frontabdeckung SP347 Ser Position bis zum hörbaren Ein Ten. Die Farbbandkassette aus dieRasten eindrücken. Das Farbband Zwischen dem Druckkopf und demDen Netzschalter des Druckers in Aus-Stellung stellen Einlegen DES PapiersEinzuziehen Diese ca cm anheben und nach vorne ziehen Mm großen Abstand zwischen Stellen Sie Die linke und rechteDer Papierführung und der Kante Des Papiers und befestigen Sie denDeutsch Automatische Abschneideinheit Unteres Papier Taste on Line BedienfeldPage Indice Caricamento Della Cartuccia DEL Nastro Rimozione del coperchio anteriore SP347 Stro girare la manopola di avanza Per eliminare allentamenti del naMento del nastro sulla cartuccia del Allineare la guida della cartucciaCaricamento Della Carta Regolazione delle guide della Carta SP317 Rimozione del coperchio poste Riore SP347 Posizione della leva di 10 Caricamento della carta SP347 Rimozione della carta in rotolo Interruttore on Line Pannello DI ControlloPage RS-232C AppendixRS-422A option MA current loop optionInterface Connections Serial Intefface This connector mates with an Amphenol 57-30360 connector Connectors and Signals Parallel InterfaceDrive output 24V, max .0 a Select the printing status one line down when pressed once Dot Alignment Adjust ModeAppendix Characters General SpecificationsAppendix 169 W × 330 D × 170 H m Approx .3 kg Tion169 W × 330 D × 176 H mm Approx 4.6 kg Memo Overseas Subsidiary Companies Star Micronics AMERICA, INC