Xantrex Technology TM500A manual Configuration, Setup, Restoring the Factory Defaults

Page 18

3.0 CONFIGURATION

Setup

The TM500A is configured at the factory for monitoring a 12 VDC system. These settings can be changed to meet specific system parameters.

The default settings are:

%

Charge Efficiency

94 %

V

Voltage (full-charge)

14.4 volts DC

A

Amperage DC

35 amps

Ah

Amp Hours

200 Hours

 

Low-Voltage Indicator

11.2 volts DC

 

Recharge Reminder

OFF

Restoring the Factory Defaults

The factory defaults can be restored to their original settings if desired. The default values will return to those listed above and are for a 12 VDC system.

To restore the factory defaults:

1.Set the TM500A into the power saving mode by repeatedly pressing the SELECT button until the LED display goes blank.

2.Press and hold the RESET button. The display will indicate “ALL” flashing in the display. Continue to hold the RESET button until the LED display remains blank.

The factory defaults are now restored.

Step 2 = ALL then blank

A L L

2

1

Figure 3-1

Resetting to Factory Defaults

12

© 2001 Xantrex Technology Inc.

 

P/N 973-0012-01-02 Rev.A05/01

Page 17 Page 19
Image 18
Page 17 Page 19
Contents TM500A Disclaimers About XantrexTrademarks Date and RevisionTable of Contents Table of Contents Important Safety Instructions Battery Safety Information Introduction TM500ATM500A TM500A NS 12/24 Volt Unpacking and InspectionTM500A 12/24 Volt TM48 48 VoltRequired Tools InstallationPre-Installation MountingSurface Mounting Surface Mounting the TM500A Using the Adaptor Communication and Remote Cable ConnectionsFlush Mounting Area To Be Cut-Out Flush Mounting the TM500AExtended Length Installations Extended Length Ground WireDeltec Shunt Mounting/Wiring the Shunt Shunt ConnectionsMounting Circuit Board to an Existing Shunt Shunt Circuit Board and HardwareConnecting the Shunt Board Circuit DiagramIn-line Fuse Restoring the Factory Defaults ConfigurationSetup Resetting to Factory DefaultsSetting Parameters Setting ParametersSetting Parameters Charge Efficiency % Setting the Charge Efficiency FactorSetting Charger Efficiency Setting Parameters Amp Hours Ah Setting the Amp HoursSetting the Amp Hours Setting Parameters Charged Indicator Setup Step a Setting the Fully-Charged Voltage LevelSetting the Charged Indicator Voltage Level Step B Switching OFF the Amperage DetectionTurn Amps OFF for Voltage only Detection Trigger on Voltage and Amperage Trigger on Voltage and Amperage Trigger on Voltage and Time Step B Setting the Time Duration Trigger on Voltage and TimeRelay Chargers Taper ChargersThree-stage Chargers Setting Parameters Low-Voltage Indicator Configuring the Low-Voltage AlarmLow-Voltage Indicator Operation Indicators and ControlsReset Button Buttons Select ButtonIndicators and Controls Basic Meters Meter Selection and LED IndicatorsAvailable Meters % state-of charge Indicators and Controls Ah AMP Hours Power Saving ModeMode Indicator LEDs BLO Low Battery Voltage Indicators and Controls Data MonitorsBHI High Battery Voltage DSF Days Since FullTo access the Data Monitor Function Reminders and Indicators To configure this functionAmp-Hour Reminder Reminders and Indicators Low-Voltage Indicator To configure this alarmReminders and Indicators Charged Indicator To reset the Charged LEDResetting the Charged Indicator Troubleshooting Symptom Possible Cause SolutionService Information Specifications SpecificationsWarranty Limited Warranty

TM500A specifications

Xantrex Technology is renowned for its innovative power solutions, and the TM500A is a standout model in its extensive product lineup. This advanced power inverter is engineered to meet the needs of both industrial applications and residential systems, providing users with reliable and efficient power conversion.

One of the main features of the TM500A is its advanced inverter technology, which allows for high efficiency and performance. With an efficiency rating often exceeding 90%, the TM500A minimizes energy loss during the conversion process. This makes it an ideal choice for renewable energy systems, such as solar and wind, by maximizing the amount of usable power delivered to connected devices. The inverter is capable of converting DC power into high-quality AC power, suitable for a wide range of appliances and electronics.

The TM500A is designed with versatility in mind. It supports various input voltage systems, allowing it to be used in a multitude of setups. This flexibility is further enhanced by its ability to operate in both grid-tied and off-grid configurations, opening up possibilities for diverse applications. Whether in a residential setting powering home appliances or in industrial applications supporting heavy machinery, the TM500A adapts to customer needs.

Another characteristic that sets the TM500A apart is its robust safety features. This inverter is equipped with multiple layers of protection, including overload, short circuit, and over-temperature safeguards. These safety measures ensure that both the device and the connected load are protected from potential damage, providing peace of mind to users.

The TM500A also boasts user-friendly interfaces, including LED indicators and diagnostic features that make monitoring performance straightforward. This ease of use is complemented by a compact and lightweight design, making installation and integration into existing systems straightforward.

Finally, Xantrex's commitment to quality is evident in the TM500A's construction, which utilizes durable materials suitable for demanding environments. Overall, the Xantrex TM500A stands as a reliable, efficient, and versatile power conversion solution that meets the evolving demands of users across various sectors. Its combination of advanced technology, safety, and user-centric design makes it a top choice for anyone needing dependable power solutions.
Top Page Image Contents