Xantrex Technology TM500A manual Connecting the Shunt Board, In-line Fuse, Circuit Diagram

Page 17

2.0 INSTALLATION

Connecting the Shunt Board

•Remove the fuse from the in-line fuse holder by rotating the fuse holder cap counterclockwise.

•Connect the ring terminal from the fuse holder to the battery’s positive terminal.

•Connect the shunt communications cable into the RJ11 jack on the shunt board. This cable can be extended up to 100 feet (30 meters).

•Replace the fuse in the fuse holder. Replace the fuse holder cap by pushing and rotating it clockwise.

To battery’s

 

To J1

 

connector on

positive

 

back of

terminal

In-line Fuse

meter

Figure 2-9

In-line Fuse

DC FUSE

DISCONNECT

+

-

+

BATTERY

SHUNT

-

INVERTER

INVERTER

SHUNT IN-LINE FUSE

SHUNT WIRE

RC4/RC8

REMOTE

JACK

GROUND WIRE

 

(IF RUN IS OVER

 

100 FEET)

 

TRACE

 

METER

 

(Back View)

J1

J2

 

REMOTE JACK

 

INVERTER ON/OFF

REMOTE CABLE

TC10, TC25, TC50, TC100

(NOT SUPPLIED)

SHUNT JACK

3507-00B-F01

Figure 2-10

Circuit Diagram

© 2001 Xantrex Technology Inc.

11

P/N 973-0012-01-02 Rev.A 05/01

Page 16 Page 18
Image 17
Page 16 Page 18
Contents TM500A Trademarks About XantrexDisclaimers Date and RevisionTable of Contents Table of Contents Important Safety Instructions Battery Safety Information TM500A IntroductionTM500A TM500A 12/24 Volt Unpacking and InspectionTM500A NS 12/24 Volt TM48 48 VoltPre-Installation InstallationRequired Tools MountingSurface Mounting Communication and Remote Cable Connections Surface Mounting the TM500A Using the AdaptorFlush Mounting Flush Mounting the TM500A Area To Be Cut-OutExtended Length Ground Wire Extended Length InstallationsShunt Connections Deltec Shunt Mounting/Wiring the ShuntShunt Circuit Board and Hardware Mounting Circuit Board to an Existing ShuntIn-line Fuse Connecting the Shunt BoardCircuit Diagram Setup ConfigurationRestoring the Factory Defaults Resetting to Factory DefaultsSetting Parameters Setting ParametersSetting Charger Efficiency Setting Parameters Charge Efficiency %Setting the Charge Efficiency Factor Setting the Amp Hours Setting Parameters Amp Hours AhSetting the Amp Hours Step a Setting the Fully-Charged Voltage Level Setting Parameters Charged Indicator SetupTurn Amps OFF for Voltage only Detection Setting the Charged Indicator Voltage LevelStep B Switching OFF the Amperage Detection Trigger on Voltage and Amperage Trigger on Voltage and Amperage Trigger on Voltage and Time Trigger on Voltage and Time Step B Setting the Time DurationThree-stage Chargers Relay ChargersTaper Chargers Low-Voltage Indicator Setting Parameters Low-Voltage IndicatorConfiguring the Low-Voltage Alarm Reset Button Indicators and ControlsOperation Buttons Select ButtonAvailable Meters % state-of charge Indicators and Controls Basic MetersMeter Selection and LED Indicators Mode Indicator LEDs Indicators and Controls Ah AMP HoursPower Saving Mode BHI High Battery Voltage Indicators and Controls Data MonitorsBLO Low Battery Voltage DSF Days Since FullTo access the Data Monitor Function Amp-Hour Reminder Reminders and IndicatorsTo configure this function To configure this alarm Reminders and Indicators Low-Voltage IndicatorResetting the Charged Indicator Reminders and Indicators Charged IndicatorTo reset the Charged LED Symptom Possible Cause Solution TroubleshootingService Information Specifications SpecificationsLimited Warranty Warranty

TM500A specifications

Xantrex Technology is renowned for its innovative power solutions, and the TM500A is a standout model in its extensive product lineup. This advanced power inverter is engineered to meet the needs of both industrial applications and residential systems, providing users with reliable and efficient power conversion.

One of the main features of the TM500A is its advanced inverter technology, which allows for high efficiency and performance. With an efficiency rating often exceeding 90%, the TM500A minimizes energy loss during the conversion process. This makes it an ideal choice for renewable energy systems, such as solar and wind, by maximizing the amount of usable power delivered to connected devices. The inverter is capable of converting DC power into high-quality AC power, suitable for a wide range of appliances and electronics.

The TM500A is designed with versatility in mind. It supports various input voltage systems, allowing it to be used in a multitude of setups. This flexibility is further enhanced by its ability to operate in both grid-tied and off-grid configurations, opening up possibilities for diverse applications. Whether in a residential setting powering home appliances or in industrial applications supporting heavy machinery, the TM500A adapts to customer needs.

Another characteristic that sets the TM500A apart is its robust safety features. This inverter is equipped with multiple layers of protection, including overload, short circuit, and over-temperature safeguards. These safety measures ensure that both the device and the connected load are protected from potential damage, providing peace of mind to users.

The TM500A also boasts user-friendly interfaces, including LED indicators and diagnostic features that make monitoring performance straightforward. This ease of use is complemented by a compact and lightweight design, making installation and integration into existing systems straightforward.

Finally, Xantrex's commitment to quality is evident in the TM500A's construction, which utilizes durable materials suitable for demanding environments. Overall, the Xantrex TM500A stands as a reliable, efficient, and versatile power conversion solution that meets the evolving demands of users across various sectors. Its combination of advanced technology, safety, and user-centric design makes it a top choice for anyone needing dependable power solutions.
Top Page Image Contents