Xantrex Technology TM500A manual Introduction

Page 7

1.0 INTRODUCTION

The TM500A

The TM500A features six data monitoring functions and three indicators including:

•State of charge/amp-hour content (full or percent of capacity)

•State of charge/voltage (real-time voltage level, historical high and low system voltage)

•Amps (real-time amps, total charging amps, total load amps)

•Amp hours removed

•Days since fully charged

•Cumulative amp hours

•Recharge indicator

•Low-voltage indicator

•Full-charge indicator

The unit is configurable for specific system or application functions such as setting the CHARGED indication parameters, battery capacity, charging efficiency, low-battery warning conditions and a recharge reminder. The TM500A can monitor any battery supply from approximately 8 to 65 volts, track energy consumption and estimate remaining battery life.

In addition to its status monitoring features, the unit can act as a remote control, switching the inverter OFF or ON (only on inverters incorporating an RC4/RC8 compatible remote control jack).

The TM500A operates on 12-, 24-, or 48-volt battery systems (48-volt systems require an optional shunt board).

14.2

Figure 1-1

The TM500A

© 2001 Xantrex Technology Inc.

1

P/N 973-0012-01-02 Rev.A05/01

Page 6 Page 8
Image 7
Page 6 Page 8
Contents TM500A Date and Revision About XantrexTrademarks DisclaimersTable of Contents Table of Contents Important Safety Instructions Battery Safety Information TM500A IntroductionTM500A TM48 48 Volt Unpacking and InspectionTM500A 12/24 Volt TM500A NS 12/24 VoltMounting InstallationPre-Installation Required ToolsSurface Mounting Communication and Remote Cable Connections Surface Mounting the TM500A Using the AdaptorFlush Mounting Flush Mounting the TM500A Area To Be Cut-OutExtended Length Ground Wire Extended Length InstallationsShunt Connections Deltec Shunt Mounting/Wiring the ShuntShunt Circuit Board and Hardware Mounting Circuit Board to an Existing ShuntCircuit Diagram Connecting the Shunt BoardIn-line Fuse Resetting to Factory Defaults ConfigurationSetup Restoring the Factory DefaultsSetting Parameters Setting ParametersSetting the Charge Efficiency Factor Setting Parameters Charge Efficiency %Setting Charger Efficiency Setting the Amp Hours Setting Parameters Amp Hours AhSetting the Amp Hours Step a Setting the Fully-Charged Voltage Level Setting Parameters Charged Indicator SetupStep B Switching OFF the Amperage Detection Setting the Charged Indicator Voltage LevelTurn Amps OFF for Voltage only Detection Trigger on Voltage and Amperage Trigger on Voltage and Amperage Trigger on Voltage and Time Trigger on Voltage and Time Step B Setting the Time DurationTaper Chargers Relay ChargersThree-stage Chargers Configuring the Low-Voltage Alarm Setting Parameters Low-Voltage IndicatorLow-Voltage Indicator Buttons Select Button Indicators and ControlsReset Button OperationMeter Selection and LED Indicators Indicators and Controls Basic MetersAvailable Meters % state-of charge Power Saving Mode Indicators and Controls Ah AMP HoursMode Indicator LEDs DSF Days Since Full Indicators and Controls Data MonitorsBHI High Battery Voltage BLO Low Battery VoltageTo access the Data Monitor Function To configure this function Reminders and IndicatorsAmp-Hour Reminder To configure this alarm Reminders and Indicators Low-Voltage IndicatorTo reset the Charged LED Reminders and Indicators Charged IndicatorResetting the Charged Indicator Symptom Possible Cause Solution TroubleshootingService Information Specifications SpecificationsLimited Warranty Warranty

TM500A specifications

Xantrex Technology is renowned for its innovative power solutions, and the TM500A is a standout model in its extensive product lineup. This advanced power inverter is engineered to meet the needs of both industrial applications and residential systems, providing users with reliable and efficient power conversion.

One of the main features of the TM500A is its advanced inverter technology, which allows for high efficiency and performance. With an efficiency rating often exceeding 90%, the TM500A minimizes energy loss during the conversion process. This makes it an ideal choice for renewable energy systems, such as solar and wind, by maximizing the amount of usable power delivered to connected devices. The inverter is capable of converting DC power into high-quality AC power, suitable for a wide range of appliances and electronics.

The TM500A is designed with versatility in mind. It supports various input voltage systems, allowing it to be used in a multitude of setups. This flexibility is further enhanced by its ability to operate in both grid-tied and off-grid configurations, opening up possibilities for diverse applications. Whether in a residential setting powering home appliances or in industrial applications supporting heavy machinery, the TM500A adapts to customer needs.

Another characteristic that sets the TM500A apart is its robust safety features. This inverter is equipped with multiple layers of protection, including overload, short circuit, and over-temperature safeguards. These safety measures ensure that both the device and the connected load are protected from potential damage, providing peace of mind to users.

The TM500A also boasts user-friendly interfaces, including LED indicators and diagnostic features that make monitoring performance straightforward. This ease of use is complemented by a compact and lightweight design, making installation and integration into existing systems straightforward.

Finally, Xantrex's commitment to quality is evident in the TM500A's construction, which utilizes durable materials suitable for demanding environments. Overall, the Xantrex TM500A stands as a reliable, efficient, and versatile power conversion solution that meets the evolving demands of users across various sectors. Its combination of advanced technology, safety, and user-centric design makes it a top choice for anyone needing dependable power solutions.
Top Page Image Contents