Xantrex Technology TM500A Operation, Indicators and Controls, Buttons Select Button, Reset Button

Page 31

4.0 OPERATION

Indicators and Controls

The TM500A contains the following controls and indicators.

•Large three-digit LED display

•Four red mode indicators

•One green CHARGED indicator

•One green INVERTER ON/OFF indicator

•Three pressure sensitive push-buttons

The three-digit LED displays alphanumeric messages with a resolution to 0.00. A negative value (–) indicator is positioned to the left of the display.

Negative

3-digit

Display

 

 

Mode

 

Indicators

 

Inverter Mode LED

Select

(on Button)

 

Inverter

 

ON/OFF

 

Button

CHARGED

Reset Button

Indicator

 

Figure 4-1

Front Panel Controls and Indicators

Buttons

SELECT Button

The SELECT button is used to switch the TM500A between the different meters and modes. One of the LEDs located above the buttons illuminate, indicating the active function.

RESET Button

The RESET button is used to change the metering parameters and to reset the CHARGED indicator.

INVERTER ON/OFF Button

The INVERTER ON/OFF button remotely controls the inverter’s ON/ OFF function via the RC4 or RC8 remote control jack. This button duplicates the function of the inverter’s power switch. The LED duplicates the indications of the RC8 remote control. Refer to the RC4/ RC8 documentation (supplied with the cable) for LED indications and modes available (depends on inverter). Remote control cables are available in 10, 25, 50 and 100 foot lengths. This button/LED does not function if a remote control cable is not connected or if the inverter does not support an RC4 or RC8 remote control.

© 2001 Xantrex Technology Inc.

25

P/N 973-0012-01-02 Rev. A 05/01

 

Page 30 Page 32
Image 31
Page 30 Page 32
Contents TM500A Date and Revision About XantrexTrademarks DisclaimersTable of Contents Table of Contents Important Safety Instructions Battery Safety Information TM500A IntroductionTM500A TM48 48 Volt Unpacking and InspectionTM500A 12/24 Volt TM500A NS 12/24 VoltMounting InstallationPre-Installation Required ToolsSurface Mounting Communication and Remote Cable Connections Surface Mounting the TM500A Using the AdaptorFlush Mounting Flush Mounting the TM500A Area To Be Cut-OutExtended Length Ground Wire Extended Length InstallationsShunt Connections Deltec Shunt Mounting/Wiring the ShuntShunt Circuit Board and Hardware Mounting Circuit Board to an Existing ShuntCircuit Diagram Connecting the Shunt BoardIn-line Fuse Resetting to Factory Defaults ConfigurationSetup Restoring the Factory DefaultsSetting Parameters Setting ParametersSetting the Charge Efficiency Factor Setting Parameters Charge Efficiency %Setting Charger Efficiency Setting the Amp Hours Setting Parameters Amp Hours AhSetting the Amp Hours Step a Setting the Fully-Charged Voltage Level Setting Parameters Charged Indicator SetupStep B Switching OFF the Amperage Detection Setting the Charged Indicator Voltage LevelTurn Amps OFF for Voltage only Detection Trigger on Voltage and Amperage Trigger on Voltage and Amperage Trigger on Voltage and Time Trigger on Voltage and Time Step B Setting the Time DurationTaper Chargers Relay ChargersThree-stage Chargers Configuring the Low-Voltage Alarm Setting Parameters Low-Voltage IndicatorLow-Voltage Indicator Buttons Select Button Indicators and ControlsReset Button OperationMeter Selection and LED Indicators Indicators and Controls Basic MetersAvailable Meters % state-of charge Power Saving Mode Indicators and Controls Ah AMP HoursMode Indicator LEDs DSF Days Since Full Indicators and Controls Data MonitorsBHI High Battery Voltage BLO Low Battery VoltageTo access the Data Monitor Function To configure this function Reminders and IndicatorsAmp-Hour Reminder To configure this alarm Reminders and Indicators Low-Voltage IndicatorTo reset the Charged LED Reminders and Indicators Charged IndicatorResetting the Charged Indicator Symptom Possible Cause Solution TroubleshootingService Information Specifications SpecificationsLimited Warranty Warranty

TM500A specifications

Xantrex Technology is renowned for its innovative power solutions, and the TM500A is a standout model in its extensive product lineup. This advanced power inverter is engineered to meet the needs of both industrial applications and residential systems, providing users with reliable and efficient power conversion.

One of the main features of the TM500A is its advanced inverter technology, which allows for high efficiency and performance. With an efficiency rating often exceeding 90%, the TM500A minimizes energy loss during the conversion process. This makes it an ideal choice for renewable energy systems, such as solar and wind, by maximizing the amount of usable power delivered to connected devices. The inverter is capable of converting DC power into high-quality AC power, suitable for a wide range of appliances and electronics.

The TM500A is designed with versatility in mind. It supports various input voltage systems, allowing it to be used in a multitude of setups. This flexibility is further enhanced by its ability to operate in both grid-tied and off-grid configurations, opening up possibilities for diverse applications. Whether in a residential setting powering home appliances or in industrial applications supporting heavy machinery, the TM500A adapts to customer needs.

Another characteristic that sets the TM500A apart is its robust safety features. This inverter is equipped with multiple layers of protection, including overload, short circuit, and over-temperature safeguards. These safety measures ensure that both the device and the connected load are protected from potential damage, providing peace of mind to users.

The TM500A also boasts user-friendly interfaces, including LED indicators and diagnostic features that make monitoring performance straightforward. This ease of use is complemented by a compact and lightweight design, making installation and integration into existing systems straightforward.

Finally, Xantrex's commitment to quality is evident in the TM500A's construction, which utilizes durable materials suitable for demanding environments. Overall, the Xantrex TM500A stands as a reliable, efficient, and versatile power conversion solution that meets the evolving demands of users across various sectors. Its combination of advanced technology, safety, and user-centric design makes it a top choice for anyone needing dependable power solutions.
Top Page Image Contents