Fujitsu 5000 user manual Hard Disk, What is a hard disk?, Handling precautions, ⁄ Point

Page 28
6 Hard Disk

6 Hard Disk

Your PC incorporates a built-in hard disk. This section outlines precautions to take when handling a hard disk.

What is a hard disk?

A hard disk is used to save software and other data and consists of a magnetic disk packed in a box as shown on the right. A hard disk can save more data and can read and write data faster than is possible with floppy disks.

Handling precautions

To prevent malfunctions, note the following precautions regarding hard disks:

-Do not move or subject the PC to shock and/or vibration with its power on.

-Do not expose to extreme temperature changes.

-Do not place in areas exposed to direct sunlight or near heating units.

-Do not store in areas subjected to shock or vibration.

-Do not store in damp or dusty areas.

-Do not expose to a strong magnetic field.

-Do not disassemble or remodel.

-Do not get wet.

Point

-Because incorrect handling may destroy data in a hard disk, back up all necessary data.

-Because there is a difference in the storage capacity of same-type hard disks, back up data for each file or segment, not for each hard disk.

18

Image 28
Contents DESKPOWER 5000 Series User’s Manual IMPORTANT SAFETY INSTRUCTIONS Greetings Command entries Conventions used in this manualWarning icons Representing keys and use thereofConventions used in the text of the manual Screen display examplesIllustrations Custom-made optionsWarning and caution labels Rear of the PC main unit Inside the PC main unitManual configuration Chapter 1 Installation and ConnectionChapter 3 Installing Internal Options Chapter 4 TroubleshootingContent InstallationSwitching on Switching offInstalling Memory Modules Installing Expansion CardsInstalling Expansion Bay Options Error MessagesStandard Specifications Cleaning Method1 Name and Function of Each Component SupplementChapter 1 Installation and Connection and explains how to connect various cables1 Installation Installation locationExample of installing the PC ⁄ PointPrecautions to be taken by the TV or radio Precautions to be taken by the PC userPreventing electromagnetic interference with a TV or radio 2 Connection Attaching CRT display, keyboard, mouse, and LAN cables ⁄ Point Connect the power cord to the CRT displaythe rear of the CRT display Connect the power cord to the outlet Connect the CRT cable to the PC main unitUpon completion of all connections Connecting the power cordDo not plug or unplug the power cord with wet hands Chapter 2 Basic Operations power on and off and handle storage mediaPress the power switch of the CRT display 1 Switching onPress the power switch of the PC main unit Wait about 10 seconds before switching the PC on or off again Turning off the power via Windows 2 Switching off1 Click Start Turning off the power via Windows NT 2 Click Shut Down3 Reset Resetting the PC via WindowsResetting the PC via Windows NT 1 Click Start and Shut DownClick Start and Shut Down Select Restart and click OKHandling precautions 4 Floppy DiskMounting and dismounting a floppy disk Mounting a floppy diskDismounting a floppy disk 1 Confirm that the floppy disk access indicator lamp is off2 Press the floppy disk eject button 5 CD-ROM Mounting and dismounting a CD-ROM disk Mounting a CD-ROMDismounting a CD-ROM 1 Press the EJECT button. The CD-ROM tray is ejectedWhat is a hard disk? 6 Hard DiskChapter 3 Installing Internal Options 1 Introduction Installing positions of internal options Removing the upper cover Removing the front panel1 Remove three screws at the rear of the PC main unit 2 Remove the upper cover2 Installing Memory Modules DIMM DIMMInstalling an additional memory Memory1 Remove the upper cover 2 Push down the hooks at both ends of the slotRemoving the memory 3 Attach the upper cover3 Installing Expansion Cards Expansion cards for PCI bus Plug & Play compatible cards Expansion card installation procedure for a PC using Windows Turning on the PC after installing theExpansion card installation procedure for a PC using Windows NTStarting and terminating the ICU For a PC using Windows NT Set up the resourcesSelect the Exit command and press the Enter key 1 If the PC is turned on, turn it offInstalling an expansion card Slide the motherboard for installing a small expansion cardInsert the expansion card into the connector Remove the slot coverInstall the motherboard when a large expansion card has been installed8 Install the retaining metal bracket at the side for installing a large expansion card4 Installing Expansion Bay Options genuine internal options in the PC expansion bay Set up the jumper switch Replacing a internal hard disk equipped as standardIf retaining metal brackets are mounted on both sides of the internal hard disk to be replaced, remove them7 Install the internal hard disk in the PC main unit 9 Attach the upper cover 10 Use BIOS setup to set the hard disk6 Replace the internal hard disk 8 Connect the cables to the hard diskInstalling internal options to 3.5-inch expansion bays both sides of the internal hard disk to be installed, remove themSet the internal option Remove the upper cover Remove the front panel8 Install the internal option in the PC main unit 7 Install a internal option in the retaining metal bracket6 Remove the retaining metal bracket from the PC main unit 10 Connect the power cord 9 Connect the flat cable11 Attach the front panel 13 Use BIOS setup to configure the internal option12 Attach the upper cover 1 Configure the internal option Installing internal options to 5-inch expansion bays5 Insert the internal option from the front side of the PC main unit Secure the internal option with two screws Connect the flat cable 8 Connect the power cord dismounted10 Attach the front panel HookUse BIOS setup to configure the internal option Attach the upper coverChapter 4 Troubleshooting as expected1 Error Messages Error messages displayed by the PCError Message Description and necessary actionTo boot booting the OS, press the F1 key. To run the BIOS Error Message Correcting errors 2 Troubleshooting The access lamp does not light upNo data is displayed on the screen The screen flickersTroubleshooting information on Windows The power is not turned on or the Power lamp on the front panelCharacters entered using the keyboard are not displayed does not light upIf an error recurs The mouse is disabled and Windows 98 cannot endThis appendix explains how to clean the PC and provides PC main unit Appendixspecifications 1 Name and Function of Each Component Front of the PC main unitMicrophone terminal Rear of the PC main unit Power-switching switch OutletVentilation holes InletMONITOR Connect the CRT cable Inside the PC main unit Power supply unit 3.5-inch expansion bayRiser board Internal hard diskMotherboard/riser board CPU JP3 jumper switchInternal battery Primary IDE connector2 Standard Specifications PC main unit specificationsDESKPOWER Product nameNumber of Storage LAN adapter specifications Sound specificationsLAN controller IntelConnector specifications CRT connectorLAN connector 100BASE-TX/10BASE-T Signal nameParallel connector Serial connectorKeyboard connector Mouse connectorUSB connector SeriesA 3 Cleaning Method Cleaning the PC main unitCleaning the keyboard Cleaning a CD-ROMCleaning a floppy disk drive Remove the ball and clean with waterClean the inside of the mouse For Windows 9X/NT modelNote on using the display Note on using an analog liquid crystal displayDisplay disturbed when the screen mode is changed 4 SupplementAbout USB Windows 98/2000 printer, modem, and speaker interfacesPower Saving Function Wake up On LANLAN Cable LAN AdapterIntel processor serial number CD-ROM driveMouse with scroll functionwheel 8th Floor Wisma Damansara Jalan Semantan 50490 Kuala Lumpur Malaysia Tel 65-776 Fax 65-776Tel 603-253 Fax 603-253
Related manuals
Manual 72 pages 40.94 Kb