Fujitsu 5000 user manual Introduction, Handling precautions

Page 30

1 Introduction

1 Introduction

The features and performance of your PC can be upgraded by installing options. This section describes the types of internal options that can be installed in the PC and explains how to remove the upper cover and front panel in preparation for installing the internal options.

■Handling precautions

Note the following when installing internal options:

-Before starting operation, switch off the PC and all connected peripherals and unplug power cords from the AC outlets.

-Immediately after the PC is turned off, internal components and units of the PC are hot. When installing and removing internal options, turn off the power and allow the PC to cool down for about 10 minutes before starting operation.

-Do not disassemble the power supply unit (a box-shaped device inside the PC).

-Do not damage or remodel internal cables or units.

-Because internal options are PC boards with exposed soldered sections that may be damaged by a static electrical charge, discharge any accumulated static electricity before handling.

-Secure the board by the metal bracket portions or an edge of the PC board such that the surface of the PC board and the soldered sections are not handled.

-Installation and disassembly of options other than Fujitsu brand products void the warranty.

20

Image 30

Contents DESKPOWER 5000 Series User’s Manual IMPORTANT SAFETY INSTRUCTIONS Greetings Warning icons Command entriesConventions used in this manual Representing keys and use thereofIllustrations Conventions used in the text of the manualScreen display examples Custom-made optionsWarning and caution labels Rear of the PC main unit Inside the PC main unitChapter 3 Installing Internal Options Manual configurationChapter 1 Installation and Connection Chapter 4 TroubleshootingSwitching on ContentInstallation Switching offInstalling Expansion Bay Options Installing Memory ModulesInstalling Expansion Cards Error Messages1 Name and Function of Each Component Standard SpecificationsCleaning Method SupplementChapter 1 Installation and Connection and explains how to connect various cablesExample of installing the PC 1 InstallationInstallation location ⁄ PointPrecautions to be taken by the PC user Precautions to be taken by the TV or radioPreventing electromagnetic interference with a TV or radio 2 Connection the rear of the CRT display Connect the power cord to the outlet Attaching CRT display, keyboard, mouse, and LAN cables ⁄ PointConnect the power cord to the CRT display Connect the CRT cable to the PC main unitConnecting the power cord Upon completion of all connectionsDo not plug or unplug the power cord with wet hands Chapter 2 Basic Operations power on and off and handle storage media1 Switching on Press the power switch of the CRT displayPress the power switch of the PC main unit Wait about 10 seconds before switching the PC on or off again 2 Switching off Turning off the power via Windows1 Click Start Turning off the power via Windows NT 2 Click Shut DownResetting the PC via Windows NT 3 ResetResetting the PC via Windows 1 Click Start and Shut DownClick Start and Shut Down Select Restart and click OKMounting and dismounting a floppy disk Handling precautions4 Floppy Disk Mounting a floppy disk1 Confirm that the floppy disk access indicator lamp is off Dismounting a floppy disk2 Press the floppy disk eject button 5 CD-ROM Dismounting a CD-ROM Mounting and dismounting a CD-ROM diskMounting a CD-ROM 1 Press the EJECT button. The CD-ROM tray is ejectedWhat is a hard disk? 6 Hard DiskChapter 3 Installing Internal Options 1 Introduction Installing positions of internal options 1 Remove three screws at the rear of the PC main unit Removing the upper coverRemoving the front panel 2 Remove the upper cover2 Installing Memory Modules DIMM DIMM1 Remove the upper cover Installing an additional memoryMemory 2 Push down the hooks at both ends of the slotRemoving the memory 3 Attach the upper cover3 Installing Expansion Cards Expansion cards for PCI bus Plug & Play compatible cards Expansion card installation procedure for a PC using Windows Turning on the PC after installing theExpansion card installation procedure for a PC using Windows NTSelect the Exit command and press the Enter key Starting and terminating the ICU For a PC using Windows NTSet up the resources 1 If the PC is turned on, turn it offInsert the expansion card into the connector Installing an expansion cardSlide the motherboard for installing a small expansion card Remove the slot cover8 Install the retaining metal bracket at the side Install the motherboard when a largeexpansion card has been installed for installing a large expansion card4 Installing Expansion Bay Options genuine internal options in the PC expansion bay If retaining metal brackets are mounted on Set up the jumper switchReplacing a internal hard disk equipped as standard both sides of the internal hard disk to be replaced, remove them6 Replace the internal hard disk 7 Install the internal hard disk in the PC main unit9 Attach the upper cover 10 Use BIOS setup to set the hard disk 8 Connect the cables to the hard diskSet the internal option Installing internal options to 3.5-inch expansion baysboth sides of the internal hard disk to be installed, remove them Remove the upper cover Remove the front panel7 Install a internal option in the retaining metal bracket 8 Install the internal option in the PC main unit6 Remove the retaining metal bracket from the PC main unit 10 Connect the power cord 9 Connect the flat cable13 Use BIOS setup to configure the internal option 11 Attach the front panel12 Attach the upper cover Installing internal options to 5-inch expansion bays 1 Configure the internal option5 Insert the internal option from the front side of the PC main unit Secure the internal option with two screws Connect the flat cable 10 Attach the front panel 8 Connect the power corddismounted HookUse BIOS setup to configure the internal option Attach the upper coverChapter 4 Troubleshooting as expectedError Message 1 Error MessagesError messages displayed by the PC Description and necessary actionTo boot booting the OS, press the F1 key. To run the BIOS Error Message Correcting errors No data is displayed on the screen 2 TroubleshootingThe access lamp does not light up The screen flickersCharacters entered using the keyboard are not displayed Troubleshooting information on WindowsThe power is not turned on or the Power lamp on the front panel does not light upIf an error recurs The mouse is disabled and Windows 98 cannot endAppendix This appendix explains how to clean the PC and provides PC main unitspecifications 1 Name and Function of Each Component Front of the PC main unitMicrophone terminal Ventilation holes Rear of the PC main unitPower-switching switch Outlet InletMONITOR Connect the CRT cable Riser board Inside the PC main unitPower supply unit 3.5-inch expansion bay Internal hard diskInternal battery Motherboard/riser boardCPU JP3 jumper switch Primary IDE connectorDESKPOWER 2 Standard SpecificationsPC main unit specifications Product nameNumber of Storage LAN controller LAN adapter specificationsSound specifications IntelLAN connector 100BASE-TX/10BASE-T Connector specificationsCRT connector Signal nameParallel connector Serial connectorMouse connector Keyboard connectorUSB connector SeriesA Cleaning the keyboard 3 Cleaning MethodCleaning the PC main unit Cleaning a CD-ROMClean the inside of the mouse Cleaning a floppy disk driveRemove the ball and clean with water For Windows 9X/NT modelDisplay disturbed when the screen mode is changed Note on using the displayNote on using an analog liquid crystal display 4 SupplementAbout USB Windows 98/2000 printer, modem, and speaker interfacesLAN Cable Power Saving FunctionWake up On LAN LAN AdapterCD-ROM drive Intel processor serial numberMouse with scroll functionwheel Tel 65-776 Fax 65-776 8th Floor Wisma Damansara Jalan Semantan 50490 Kuala Lumpur MalaysiaTel 603-253 Fax 603-253

Related manuals

Manual 72 pages 40.94 Kb