Fujitsu 5000 user manual Error Message, Description and necessary action

Page 57

Error Message	Description and necessary action

An invalid hard disk drive was set.	Confirm ‘Primary master’ or ‘Secondary master’ on the
	BIOS setup main menu. If the message is still displayed,
	contact a dealer or the your local distributor.

Turn the power off, then on again.	If the message is still displayed, contact a dealer or the
	your local distributor.

Confirm BIOS setup items, then	If the message is still displayed, contact a dealer or the
save.	your local distributor.

Because the computer was not	This message is displayed if an invalid BIOS setup value
booted correctly last time, some	is defined to boot the system, the power is turned off
of the setup values are reset to	during boot, or the computer is rebooted three or more
defaults.	times in the same operation. To continue booting, press
	the F1 key. To run the BIOS setup utility and check setup
	values, press the F2 key.

If an error occurs during POST,	To boot booting the OS, press the F1 key. To run the BIOS
this message is displayed before	setup utility and change setup values, press the F2 key.
the OS boots.

Check date and time settings	Confirm 'System Time' and 'System Date.'

47

Image 57

Contents DESKPOWER 5000 Series User’s Manual IMPORTANT SAFETY INSTRUCTIONS Greetings Conventions used in this manual Command entriesWarning icons Representing keys and use thereofScreen display examples Conventions used in the text of the manualIllustrations Custom-made optionsRear of the PC main unit Inside the PC main unit Warning and caution labelsChapter 1 Installation and Connection Manual configurationChapter 3 Installing Internal Options Chapter 4 TroubleshootingInstallation ContentSwitching on Switching offInstalling Expansion Cards Installing Memory ModulesInstalling Expansion Bay Options Error MessagesCleaning Method Standard Specifications1 Name and Function of Each Component Supplementand explains how to connect various cables Chapter 1 Installation and ConnectionInstallation location 1 InstallationExample of installing the PC ⁄ PointPrecautions to be taken by the PC user Precautions to be taken by the TV or radioPreventing electromagnetic interference with a TV or radio 2 Connection Connect the power cord to the CRT display Attaching CRT display, keyboard, mouse, and LAN cables ⁄ Pointthe rear of the CRT display Connect the power cord to the outlet Connect the CRT cable to the PC main unitConnecting the power cord Upon completion of all connectionsDo not plug or unplug the power cord with wet hands power on and off and handle storage media Chapter 2 Basic Operations1 Switching on Press the power switch of the CRT displayPress the power switch of the PC main unit Wait about 10 seconds before switching the PC on or off again 2 Switching off Turning off the power via Windows1 Click Start 2 Click Shut Down Turning off the power via Windows NTResetting the PC via Windows 3 ResetResetting the PC via Windows NT 1 Click Start and Shut DownSelect Restart and click OK Click Start and Shut Down4 Floppy Disk Handling precautionsMounting and dismounting a floppy disk Mounting a floppy disk1 Confirm that the floppy disk access indicator lamp is off Dismounting a floppy disk2 Press the floppy disk eject button 5 CD-ROM Mounting a CD-ROM Mounting and dismounting a CD-ROM diskDismounting a CD-ROM 1 Press the EJECT button. The CD-ROM tray is ejected6 Hard Disk What is a hard disk?Chapter 3 Installing Internal Options 1 Introduction Installing positions of internal options Removing the front panel Removing the upper cover1 Remove three screws at the rear of the PC main unit 2 Remove the upper coverDIMM DIMM 2 Installing Memory ModulesMemory Installing an additional memory1 Remove the upper cover 2 Push down the hooks at both ends of the slot3 Attach the upper cover Removing the memory3 Installing Expansion Cards Expansion cards for PCI bus Plug & Play compatible cards Turning on the PC after installing the Expansion card installation procedure for a PC using WindowsWindows NT Expansion card installation procedure for a PC usingSet up the resources Starting and terminating the ICU For a PC using Windows NTSelect the Exit command and press the Enter key 1 If the PC is turned on, turn it offSlide the motherboard for installing a small expansion card Installing an expansion cardInsert the expansion card into the connector Remove the slot coverexpansion card has been installed Install the motherboard when a large8 Install the retaining metal bracket at the side for installing a large expansion card4 Installing Expansion Bay Options genuine internal options in the PC expansion bay Replacing a internal hard disk equipped as standard Set up the jumper switchIf retaining metal brackets are mounted on both sides of the internal hard disk to be replaced, remove them9 Attach the upper cover 10 Use BIOS setup to set the hard disk 7 Install the internal hard disk in the PC main unit6 Replace the internal hard disk 8 Connect the cables to the hard diskboth sides of the internal hard disk to be installed, remove them Installing internal options to 3.5-inch expansion baysSet the internal option Remove the upper cover Remove the front panel7 Install a internal option in the retaining metal bracket 8 Install the internal option in the PC main unit6 Remove the retaining metal bracket from the PC main unit 9 Connect the flat cable 10 Connect the power cord13 Use BIOS setup to configure the internal option 11 Attach the front panel12 Attach the upper cover Installing internal options to 5-inch expansion bays 1 Configure the internal option5 Insert the internal option from the front side of the PC main unit Secure the internal option with two screws Connect the flat cable dismounted 8 Connect the power cord10 Attach the front panel HookAttach the upper cover Use BIOS setup to configure the internal optionas expected Chapter 4 TroubleshootingError messages displayed by the PC 1 Error MessagesError Message Description and necessary actionTo boot booting the OS, press the F1 key. To run the BIOS Description and necessary action Correcting errors The access lamp does not light up 2 TroubleshootingNo data is displayed on the screen The screen flickersThe power is not turned on or the Power lamp on the front panel Troubleshooting information on WindowsCharacters entered using the keyboard are not displayed does not light upThe mouse is disabled and Windows 98 cannot end If an error recursAppendix This appendix explains how to clean the PC and provides PC main unitspecifications Front of the PC main unit 1 Name and Function of Each ComponentMicrophone terminal Power-switching switch Outlet Rear of the PC main unitVentilation holes InletMONITOR Connect the CRT cable Power supply unit 3.5-inch expansion bay Inside the PC main unitRiser board Internal hard diskCPU JP3 jumper switch Motherboard/riser boardInternal battery Primary IDE connectorPC main unit specifications 2 Standard SpecificationsDESKPOWER Product nameNumber of Storage Sound specifications LAN adapter specificationsLAN controller IntelCRT connector Connector specificationsLAN connector 100BASE-TX/10BASE-T Signal nameSerial connector Parallel connectorMouse connector Keyboard connectorUSB connector SeriesA Cleaning the PC main unit 3 Cleaning MethodCleaning the keyboard Cleaning a CD-ROMRemove the ball and clean with water Cleaning a floppy disk driveClean the inside of the mouse For Windows 9X/NT modelNote on using an analog liquid crystal display Note on using the displayDisplay disturbed when the screen mode is changed 4 Supplementprinter, modem, and speaker interfaces About USB Windows 98/2000Wake up On LAN Power Saving FunctionLAN Cable LAN AdapterCD-ROM drive Intel processor serial numberMouse with scroll functionwheel Tel 65-776 Fax 65-776 8th Floor Wisma Damansara Jalan Semantan 50490 Kuala Lumpur MalaysiaTel 603-253 Fax 603-253

Related manuals

Manual 72 pages 40.94 Kb