Fujitsu 5000 user manual Switching off, Turning off the power via Windows, Click Start, ⁄ Point

Page 20

2 Switching off

2 Switching off

This section explains how to turn off the PC.

⁄Point

- Before turning off the power, terminate all jobs and save all necessary data.

- Before turning off the power, confirm that the access indicator lamps ( see Appendix 1, "Name and Function of Each Component") of the floppy and hard disk drives are off. If the power is turned off while the access indicator lamps are on, data may be lost or data in the floppy disk or hard disk may be destroyed.

-If the power cord is unplugged from the outlet or the power is disconnected due to a power failure while the PC is on, re-connect he power cord or wait until AC power recovers. When the power recovers, the PC is automatically turned on and started. "Press <F2> to enter SETUP" may be displayed at this time. In this case, press the [F2] key, check the Setup items from the menu, and restart the PC.

-Do not turn off the PC while the POST is operating. To switch off the PC while the POST is operating, press the power switch for at least four seconds and confirm that the power lamp goes off.

-If the power is turned off during the POST operation due to a power failure or some other reason, the message, [Press <F1> to resume, <F2> to setup], may be displayed at rebooting. In this case, press [F2] key, confirm the setup menu, and then reboot.

-If the power lamp is on in orange, repress the power switch for at least four seconds.

■Turning off the power via Windows 98

1 Click [Start].

The "Start" menu appears.

For Windows 98

10

Image 20

Contents DESKPOWER 5000 Series User’s Manual IMPORTANT SAFETY INSTRUCTIONS Greetings Command entries Conventions used in this manualWarning icons Representing keys and use thereofConventions used in the text of the manual Screen display examplesIllustrations Custom-made optionsWarning and caution labels Rear of the PC main unit Inside the PC main unitManual configuration Chapter 1 Installation and ConnectionChapter 3 Installing Internal Options Chapter 4 TroubleshootingContent InstallationSwitching on Switching offInstalling Memory Modules Installing Expansion CardsInstalling Expansion Bay Options Error MessagesStandard Specifications Cleaning Method1 Name and Function of Each Component SupplementChapter 1 Installation and Connection and explains how to connect various cables1 Installation Installation locationExample of installing the PC ⁄ PointPreventing electromagnetic interference with a TV or radio Precautions to be taken by the PC userPrecautions to be taken by the TV or radio 2 Connection Attaching CRT display, keyboard, mouse, and LAN cables ⁄ Point Connect the power cord to the CRT displaythe rear of the CRT display Connect the power cord to the outlet Connect the CRT cable to the PC main unitDo not plug or unplug the power cord with wet hands Connecting the power cordUpon completion of all connections Chapter 2 Basic Operations power on and off and handle storage mediaPress the power switch of the PC main unit 1 Switching onPress the power switch of the CRT display Wait about 10 seconds before switching the PC on or off again 1 Click Start 2 Switching offTurning off the power via Windows Turning off the power via Windows NT 2 Click Shut Down3 Reset Resetting the PC via WindowsResetting the PC via Windows NT 1 Click Start and Shut DownClick Start and Shut Down Select Restart and click OKHandling precautions 4 Floppy DiskMounting and dismounting a floppy disk Mounting a floppy disk2 Press the floppy disk eject button 1 Confirm that the floppy disk access indicator lamp is offDismounting a floppy disk 5 CD-ROM Mounting and dismounting a CD-ROM disk Mounting a CD-ROMDismounting a CD-ROM 1 Press the EJECT button. The CD-ROM tray is ejectedWhat is a hard disk? 6 Hard DiskChapter 3 Installing Internal Options 1 Introduction Installing positions of internal options Removing the upper cover Removing the front panel1 Remove three screws at the rear of the PC main unit 2 Remove the upper cover2 Installing Memory Modules DIMM DIMMInstalling an additional memory Memory1 Remove the upper cover 2 Push down the hooks at both ends of the slotRemoving the memory 3 Attach the upper cover3 Installing Expansion Cards Expansion cards for PCI bus Plug & Play compatible cards Expansion card installation procedure for a PC using Windows Turning on the PC after installing theExpansion card installation procedure for a PC using Windows NTStarting and terminating the ICU For a PC using Windows NT Set up the resourcesSelect the Exit command and press the Enter key 1 If the PC is turned on, turn it offInstalling an expansion card Slide the motherboard for installing a small expansion cardInsert the expansion card into the connector Remove the slot coverInstall the motherboard when a large expansion card has been installed8 Install the retaining metal bracket at the side for installing a large expansion card4 Installing Expansion Bay Options genuine internal options in the PC expansion bay Set up the jumper switch Replacing a internal hard disk equipped as standardIf retaining metal brackets are mounted on both sides of the internal hard disk to be replaced, remove them7 Install the internal hard disk in the PC main unit 9 Attach the upper cover 10 Use BIOS setup to set the hard disk6 Replace the internal hard disk 8 Connect the cables to the hard diskInstalling internal options to 3.5-inch expansion bays both sides of the internal hard disk to be installed, remove themSet the internal option Remove the upper cover Remove the front panel6 Remove the retaining metal bracket from the PC main unit 7 Install a internal option in the retaining metal bracket8 Install the internal option in the PC main unit 10 Connect the power cord 9 Connect the flat cable12 Attach the upper cover 13 Use BIOS setup to configure the internal option11 Attach the front panel 5 Insert the internal option from the front side of the PC main unit Installing internal options to 5-inch expansion bays1 Configure the internal option Secure the internal option with two screws Connect the flat cable 8 Connect the power cord dismounted10 Attach the front panel HookUse BIOS setup to configure the internal option Attach the upper coverChapter 4 Troubleshooting as expected1 Error Messages Error messages displayed by the PCError Message Description and necessary actionTo boot booting the OS, press the F1 key. To run the BIOS Error Message Correcting errors 2 Troubleshooting The access lamp does not light upNo data is displayed on the screen The screen flickersTroubleshooting information on Windows The power is not turned on or the Power lamp on the front panelCharacters entered using the keyboard are not displayed does not light upIf an error recurs The mouse is disabled and Windows 98 cannot endspecifications AppendixThis appendix explains how to clean the PC and provides PC main unit 1 Name and Function of Each Component Front of the PC main unitMicrophone terminal Rear of the PC main unit Power-switching switch OutletVentilation holes InletMONITOR Connect the CRT cable Inside the PC main unit Power supply unit 3.5-inch expansion bayRiser board Internal hard diskMotherboard/riser board CPU JP3 jumper switchInternal battery Primary IDE connector2 Standard Specifications PC main unit specificationsDESKPOWER Product nameNumber of Storage LAN adapter specifications Sound specificationsLAN controller IntelConnector specifications CRT connectorLAN connector 100BASE-TX/10BASE-T Signal nameParallel connector Serial connectorUSB connector SeriesA Mouse connectorKeyboard connector 3 Cleaning Method Cleaning the PC main unitCleaning the keyboard Cleaning a CD-ROMCleaning a floppy disk drive Remove the ball and clean with waterClean the inside of the mouse For Windows 9X/NT modelNote on using the display Note on using an analog liquid crystal displayDisplay disturbed when the screen mode is changed 4 SupplementAbout USB Windows 98/2000 printer, modem, and speaker interfacesPower Saving Function Wake up On LANLAN Cable LAN AdapterMouse with scroll functionwheel CD-ROM driveIntel processor serial number Tel 603-253 Fax 603-253 Tel 65-776 Fax 65-7768th Floor Wisma Damansara Jalan Semantan 50490 Kuala Lumpur Malaysia

Related manuals

Manual 72 pages 40.94 Kb