Fujitsu 5000 Installing internal options to 5-inch expansion bays, Configure the internal option

Page 51

■Installing internal options to 5-inch expansion bays

This section explains how to install 5-inch expansion bay options such as CD-ROM drive and 5- inch floppy disk drive. A CD-ROM drive is used below in an example of installation. Up to two 5- inch expansion bay options can be installed in your PC.

⁄Point

The retaining metal bracket is required for installing a 3.5-inch hard disk or magneto-optic disk drive.

Retaining metal bracket

1 Configure the internal option.

See the manual accompanying the internal options to configure the following items.

-To install an IDE-standard internal option: Set the master, slave, and cable select.

-To install a SCSI interface internal option: Configure the SCSI ID.

Remove the upper cover.

Remove the front panel.

4 Remove the blank panel (for installing the internal option to the lower 5-inch expansion bay).

Remove a screw to remove the blank panel.

5 Insert the internal option from the front side

of the PC main unit

Image 51

Contents DESKPOWER 5000 Series User’s Manual IMPORTANT SAFETY INSTRUCTIONS Greetings Representing keys and use thereof Command entriesConventions used in this manual Warning iconsCustom-made options Conventions used in the text of the manualScreen display examples IllustrationsRear of the PC main unit Inside the PC main unit Warning and caution labelsChapter 4 Troubleshooting Manual configurationChapter 1 Installation and Connection Chapter 3 Installing Internal OptionsSwitching off ContentInstallation Switching onError Messages Installing Memory ModulesInstalling Expansion Cards Installing Expansion Bay OptionsSupplement Standard SpecificationsCleaning Method 1 Name and Function of Each Componentand explains how to connect various cables Chapter 1 Installation and Connection⁄ Point 1 InstallationInstallation location Example of installing the PCPrecautions to be taken by the PC user Precautions to be taken by the TV or radioPreventing electromagnetic interference with a TV or radio 2 Connection Connect the CRT cable to the PC main unit Attaching CRT display, keyboard, mouse, and LAN cables ⁄ PointConnect the power cord to the CRT display the rear of the CRT display Connect the power cord to the outletConnecting the power cord Upon completion of all connectionsDo not plug or unplug the power cord with wet hands power on and off and handle storage media Chapter 2 Basic Operations1 Switching on Press the power switch of the CRT displayPress the power switch of the PC main unit Wait about 10 seconds before switching the PC on or off again 2 Switching off Turning off the power via Windows1 Click Start 2 Click Shut Down Turning off the power via Windows NT1 Click Start and Shut Down 3 ResetResetting the PC via Windows Resetting the PC via Windows NTSelect Restart and click OK Click Start and Shut DownMounting a floppy disk Handling precautions4 Floppy Disk Mounting and dismounting a floppy disk1 Confirm that the floppy disk access indicator lamp is off Dismounting a floppy disk2 Press the floppy disk eject button 5 CD-ROM 1 Press the EJECT button. The CD-ROM tray is ejected Mounting and dismounting a CD-ROM diskMounting a CD-ROM Dismounting a CD-ROM6 Hard Disk What is a hard disk?Chapter 3 Installing Internal Options 1 Introduction Installing positions of internal options 2 Remove the upper cover Removing the upper coverRemoving the front panel 1 Remove three screws at the rear of the PC main unitDIMM DIMM 2 Installing Memory Modules2 Push down the hooks at both ends of the slot Installing an additional memoryMemory 1 Remove the upper cover3 Attach the upper cover Removing the memory3 Installing Expansion Cards Expansion cards for PCI bus Plug & Play compatible cards Turning on the PC after installing the Expansion card installation procedure for a PC using WindowsWindows NT Expansion card installation procedure for a PC using1 If the PC is turned on, turn it off Starting and terminating the ICU For a PC using Windows NTSet up the resources Select the Exit command and press the Enter keyRemove the slot cover Installing an expansion cardSlide the motherboard for installing a small expansion card Insert the expansion card into the connectorfor installing a large expansion card Install the motherboard when a largeexpansion card has been installed 8 Install the retaining metal bracket at the side4 Installing Expansion Bay Options genuine internal options in the PC expansion bay both sides of the internal hard disk to be replaced, remove them Set up the jumper switchReplacing a internal hard disk equipped as standard If retaining metal brackets are mounted on8 Connect the cables to the hard disk 7 Install the internal hard disk in the PC main unit9 Attach the upper cover 10 Use BIOS setup to set the hard disk 6 Replace the internal hard diskRemove the upper cover Remove the front panel Installing internal options to 3.5-inch expansion baysboth sides of the internal hard disk to be installed, remove them Set the internal option7 Install a internal option in the retaining metal bracket 8 Install the internal option in the PC main unit6 Remove the retaining metal bracket from the PC main unit 9 Connect the flat cable 10 Connect the power cord13 Use BIOS setup to configure the internal option 11 Attach the front panel12 Attach the upper cover Installing internal options to 5-inch expansion bays 1 Configure the internal option5 Insert the internal option from the front side of the PC main unit Secure the internal option with two screws Connect the flat cable Hook 8 Connect the power corddismounted 10 Attach the front panelAttach the upper cover Use BIOS setup to configure the internal optionas expected Chapter 4 TroubleshootingDescription and necessary action 1 Error MessagesError messages displayed by the PC Error MessageTo boot booting the OS, press the F1 key. To run the BIOS Description and necessary action Correcting errors The screen flickers 2 TroubleshootingThe access lamp does not light up No data is displayed on the screendoes not light up Troubleshooting information on WindowsThe power is not turned on or the Power lamp on the front panel Characters entered using the keyboard are not displayedThe mouse is disabled and Windows 98 cannot end If an error recursAppendix This appendix explains how to clean the PC and provides PC main unitspecifications Front of the PC main unit 1 Name and Function of Each ComponentMicrophone terminal Inlet Rear of the PC main unitPower-switching switch Outlet Ventilation holesMONITOR Connect the CRT cable Internal hard disk Inside the PC main unitPower supply unit 3.5-inch expansion bay Riser boardPrimary IDE connector Motherboard/riser boardCPU JP3 jumper switch Internal batteryProduct name 2 Standard SpecificationsPC main unit specifications DESKPOWERNumber of Storage Intel LAN adapter specificationsSound specifications LAN controllerSignal name Connector specificationsCRT connector LAN connector 100BASE-TX/10BASE-TSerial connector Parallel connectorMouse connector Keyboard connectorUSB connector SeriesA Cleaning a CD-ROM 3 Cleaning MethodCleaning the PC main unit Cleaning the keyboardFor Windows 9X/NT model Cleaning a floppy disk driveRemove the ball and clean with water Clean the inside of the mouse4 Supplement Note on using the displayNote on using an analog liquid crystal display Display disturbed when the screen mode is changedprinter, modem, and speaker interfaces About USB Windows 98/2000LAN Adapter Power Saving FunctionWake up On LAN LAN CableCD-ROM drive Intel processor serial numberMouse with scroll functionwheel Tel 65-776 Fax 65-776 8th Floor Wisma Damansara Jalan Semantan 50490 Kuala Lumpur MalaysiaTel 603-253 Fax 603-253

Related manuals

Manual 72 pages 40.94 Kb