Fujitsu
BX960 S1
manual
Technical data
Troubleshooting
Specifications
Install
Error codes
Index Fault
Connecting devices
Configuring the Server Blade
Bios Setup security functions
Bios
Cleaning the Server Blade
Page 20
Technical data
20
Operating Manual
BX960 S1
Page 19
Page 21
Image 20
Page 19
Page 21
Contents
Primergy BX960 S1 Server Blade
Comments… Suggestions… Corrections…
Certified documentation according to DIN EN ISO
For your safety
High safety use
Radio interference
Aluminum electrolytic capacitors
Only for the Japanese market About Sata hard disk drives
Measures against momentary voltage drop
Harmonic Current Standards
Only for the Japanese market
Operating Manual
Contents
Contents
Introduction
Concept and target groups for this manual
Documentation overview
Documentation overview
Customer Self Service CSS
Performance features
Performance features Further sources of information
Performance features
System board
Trusted Platform Module TPM
Slots for expansion cards
SSD drives
SATA-RAID support
Graphics controller
External ports
IRMC S2 with integrated management LAN connector
Server management
Performance features ServerView Installation Manager
Service and support
Notational conventions
Notational conventions
Technical data
Technical data
Electrical data
Compliance with regulations and standards
Technical data Certification
Mechanical specifications
Weight
Ambient conditions
Technical data
Overview Installation steps
BX960 S1
Safety instructions
Important notes
Safety instructions Before starting up
Installation and operation
Safety instructions
Safety instructions Batteries
Operating Manual
Laser information
Never remove parts of the optical drive casing
ESD label
CE conformity
FCC class a device
Transporting the Server Blade
CE conformity Other important information
Environmental protection
Environmentally-friendly product design and development
Energy-saving information
Packaging information
Returns, recycling and disposal
Environmental protection
Labels on plastic casing parts
Hours
Installing the hardware
Minimum acclimatization time
Unpacking the server
Installing the Server Blade in the system unit
Unpacking the server
Removing the server blade dummy module
Installing the Server Blade
Installing the Server Blade
Connecting devices
Connecting devices
SAN
Instructions for connecting/disconnecting cables
Instructions for connecting/disconnecting cables
Connecting cables
Disconnecting cables
Instructions for connecting/disconnecting cables
Installation and operation
Control and display elements
Control and display elements Control elements
LEDs on the control panel
Control and display elements
CSS
ID card
Switching the Server Blade on and off
Switching the Server Blade on and off
Defined switch-on/off time
Other On/Off options After power failure
Configuring the Server Blade
Configuring the Server Blade
Advantages of the ServerView Installation Manager
Onboard Sata controller, configuring
Installing the operating system
Cleaning the Server Blade
Cleaning the Server Blade
Cleaning the Server Blade
Bios Setup security functions
Preventing unauthorized Bios Setup calls
Preventing unauthorized system access
Property and data protection
Protecting Bios from being overwritten
Protecting the server from being switched off by a program
Troubleshooting and tips
Server switches itself off
Server Management has detected an error
Monitor is switched off
Power cable or monitor cable not connected
Flickering stripes on monitor screen1
Flickering stripes on monitor screen Screen has gone blank
Brightness control is set to dark
System will not boot
SAS configuration incorrect
No screen display or display drifts1
Incorrect date and time
Hard disk drive error messages at system boot
RAID controller configuration incorrect
Error message on screen
RAID controller is not configured for this drive
Added drive reported as defective
Added drive reported as defective
Error message on screen
Replacing CSS components
SSD drive
SSD drive
Opening the server blade
Removing the server blade from the system unit
SSD drive Removing the cover
Removing the cover
Replacing the SSD drive
Removing an SSD drive
Removing the SSD drive mounting frame
SSD drive Installing an SSD drive
Fitting the SSD drive into the guide element
Inserting the SSD drive in the mounting frame
Installing the mezzanine cards carrier
Closing the server blade
Bios
Index
Index Fault
CSS
Index
UFM
Weight Operating Manual
Related pages
All TechnicalData page
Technical data for Philips CDR-777
Technical Data for Graco Inc 238338
Technical Data for Zanussi SPE2015CC
Top
Page
Image
Contents