Fujitsu TX150 S3 manual Procedure

Page 13

2 Procedure

VCAUTION!

The actions described in these instructions should only be performed by technicians, service personnel or technical specialists. Equipment repairs should only be performed by authorized, qualified staff. Any unauthorized opening and improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) and could also damage the equipment. Please note that any unauthorized opening of the device will result in the invalidation of the warranty and exclusion from all liability.

ÊFirst of all please familiarize yourself with the safety instructions in the section chapter “Safety notes” on page 7 et seqq. .

ÊEnsure that all required manuals (see “Additional documentation about the server” on page 1) are available, printing out the PDF files if necessary. You will definitely need the Operating Manual for the server and the Technical Manual for the system board.

ÊShut down the server correctly, switch it off, pull out the power plug(s), and open the server as described in the chapter “Preparation” on page 13 et seqq. .

ÊExtend or upgrade your server as described in the relevant chapter.

IThe Operating Manual for the server describes how you install/remove the hot-plug components.

IProcedures which are identical for the floorstand and rack models are only described for the floorstand model.

ÊClose the server, connect it to the power outlet, and switch it on as described in the chapter “Completion” on page 59 et seqq. .

ÊStart the operating system and, if necessary, configure it as required (see the Operating Manual).

U41604-Z156-1-76

Options Guide

5

Image 13
Contents Primergy TX150 S3 Server System Copyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO Page Page Page Page Contents Contents Overview of the documentation IntroductionConcept and target groups Additional documentation about the serverExtensions and conversions Extensions and conversionsFurther sources of information Extension of the main memoryIntroduction Additional accessible drivesHard disks extension box Additional controllers in the PCI slotsNotational conventions Conversion standard power supply to hot-plug power supplyNotational conventions Conversion of the floorstand model to a rack modelProcedure Page Before operating the device Safety notesSafety notes Installation and operation Safety notes Safety notes Batteries Never remove parts of the CD-/DVD-ROM drive assembly Safety notes Modules with electrostatic-sensitive components Floorstand model PreparationOpening the server Floorstand model Removing the front coverPreparation Removing the hard disk coverRack model Rack modelRack model Loosening the screws Removing the rack front cover Removing the rack front coverPage Equipping rules Main memoryExtending/replacing the main memory Extending/replacing the main memoryInserting a memory module Main memoryPage Installing an accessible 5.25-inch drive Accessible drivesAttaching the EasyClick rails DVD-ROM burner Installing an accessible 5.25-inch driveAccessible drives Attaching the EasyClick rails magnetic tape drive VXA-2 Installing the hard disks extension box Attaching the EasyClick rails Installing the hard disks extension boxPCIe Slot PCI Slot Controller in the PCI slotsInstalling a controller Installing a controllerController in the PCI slots Installing a controllerPCI slot assembling PCI slot assemblingRemoteView components RemoteView Service Board S2 LPRemoteView components RSB S2 LP RemoteView Service Board S2 LP External Scsi interface Installing the external Scsi interfacePage Conversion standard PS to hot- plug PS Taking out the standard power supply Installing the Power backplane in the PS cage Installing the PS cage Fastening the PS cage in the housing Fastening the PS cage at the rear side Inserting the power supply module Locking the power supply module Installing the dummy cover Mounting the anti-tilt bracket Fastening the anti-tilt bracket Page Removing the anti-tilt bracket Converting from the floorstand model to the rack modelRight-hand side cover and the top cover build one part Removing the rubber feet Installing the operating panel module Converting from the floorstand model to the rack model Page Attaching the hard disk cover CompletionAttaching the front cover Attaching the front coverCompletion Closing the serverAttaching the plastic front cover Attaching the rack front coverAttaching the rack front cover Attaching the top cover Installing the server in a rack cabinet Fastening the server in the rack cabinet Rack model CompletionCabling AppendixScsi version Channel Scsi version with onboard Scsi controllerScsi RAID CablingIDE/FD Data Cable prefix T26139 Controller Sata versionPage Abbreviations Abbreviations HDD MRL SCA Page Related publications Related Publications Index Page Comments Suggestions Corrections Page Comments Suggestions Corrections Page Hinweise zum vorliegenden Dokument Information on this document