Fujitsu TX150 S3 manual Safety notes, Before operating the device

Page 15

3 Safety notes

IThe following safety notes are also provided in the “Safety” manual.

This device complies with the relevant safety regulations for data processing equipment.

If you have any questions about where you can set up the device, contact your sales outlet or our customer service team.

VCAUTION!

The actions described in these instructions should only be performed by technicians, service personnel or technical specialists. Equipment repairs should only be performed by authorized, qualified staff. Any unauthorized openings and improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) and could also damage the equipment. Please note that any unauthorized openings of the device will result in the invalidation of the warranty and exclusion from all liability.

Before operating the device

VCAUTION!

During installation and before operating the device, observe the instructions on environmental conditions for your device.

If the device is brought in from a cold environment, condensation may form both inside and on the outside of the machine.

Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed.

Transport the device only in the original packaging or in packaging that protects it from knocks and jolts.

U41604-Z156-1-76

Options Guide

7

Image 15
Contents Primergy TX150 S3 Server System Comments… Suggestions… Corrections… Copyright and TrademarksCertified documentation according to DIN EN ISO Page Page Page Page Contents Contents Additional documentation about the server IntroductionOverview of the documentation Concept and target groupsExtension of the main memory Extensions and conversionsExtensions and conversions Further sources of informationAdditional controllers in the PCI slots Additional accessible drivesIntroduction Hard disks extension boxConversion of the floorstand model to a rack model Conversion standard power supply to hot-plug power supplyNotational conventions Notational conventionsProcedure Page Before operating the device Safety notesSafety notes Installation and operation Safety notes Safety notes Batteries Never remove parts of the CD-/DVD-ROM drive assembly Safety notes Modules with electrostatic-sensitive components Preparation Floorstand modelOpening the server Floorstand model Removing the front coverPreparation Removing the hard disk coverRack model Rack modelRack model Loosening the screws Removing the rack front cover Removing the rack front coverPage Equipping rules Main memoryExtending/replacing the main memory Extending/replacing the main memoryInserting a memory module Main memoryPage Installing an accessible 5.25-inch drive Accessible drivesAttaching the EasyClick rails DVD-ROM burner Installing an accessible 5.25-inch driveAccessible drives Attaching the EasyClick rails magnetic tape drive VXA-2 Installing the hard disks extension box Attaching the EasyClick rails Installing the hard disks extension boxPCIe Slot PCI Slot Controller in the PCI slotsInstalling a controller Installing a controllerController in the PCI slots Installing a controllerPCI slot assembling PCI slot assemblingRemoteView components RemoteView Service Board S2 LPRemoteView components RSB S2 LP RemoteView Service Board S2 LP External Scsi interface Installing the external Scsi interfacePage Conversion standard PS to hot- plug PS Taking out the standard power supply Installing the Power backplane in the PS cage Installing the PS cage Fastening the PS cage in the housing Fastening the PS cage at the rear side Inserting the power supply module Locking the power supply module Installing the dummy cover Mounting the anti-tilt bracket Fastening the anti-tilt bracket Page Removing the anti-tilt bracket Converting from the floorstand model to the rack modelRight-hand side cover and the top cover build one part Removing the rubber feet Installing the operating panel module Converting from the floorstand model to the rack model Page Attaching the hard disk cover CompletionAttaching the front cover Attaching the front coverCompletion Closing the serverAttaching the plastic front cover Attaching the rack front coverAttaching the rack front cover Attaching the top cover Installing the server in a rack cabinet Fastening the server in the rack cabinet Rack model CompletionChannel Scsi version with onboard Scsi controller AppendixCabling Scsi versionScsi RAID CablingIDE/FD Data Cable prefix T26139 Controller Sata versionPage Abbreviations Abbreviations HDD MRL SCA Page Related publications Related Publications Index Page Comments Suggestions Corrections Page Comments Suggestions Corrections Page Hinweise zum vorliegenden Dokument Information on this document