Fujitsu TX150 S3 manual Safety notes Modules with electrostatic-sensitive components

Page 20

Safety notes

Modules with electrostatic-sensitive components:

Systems and components that might be damaged by electrostatic discharge (ESD) are marked with the following label:

Figure 1: ESD label

When you handle components fitted with ESDs, you must observe the following points under all circumstances:

Remove the power plug from the power socket before inserting or removing components containing ESDs.

You must always discharge yourself of static charges (e.g. by touching a grounded object) before working.

The equipment and tools you use must be free of static charges.

Only touch the components at the positions highlighted in green (touch points).

Do not touch any exposed pins or conductors on a component.

Use a grounding cable designed for this purpose to connect yourself to the system unit as you install components.

Place all components on a static-safe base.

IYou will find a detailed description for handling ESD components in the relevant European or international standards (DIN EN 61340-5-1, ANSI/ESD S20.20).

12

Options Guide

U41604-Z156-1-76

Image 20
Contents Primergy TX150 S3 Server System Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Copyright and Trademarks Page Page Page Page Contents Contents Introduction Overview of the documentationConcept and target groups Additional documentation about the serverExtensions and conversions Extensions and conversionsFurther sources of information Extension of the main memoryAdditional accessible drives IntroductionHard disks extension box Additional controllers in the PCI slotsConversion standard power supply to hot-plug power supply Notational conventionsNotational conventions Conversion of the floorstand model to a rack modelProcedure Page Safety notes Before operating the deviceSafety notes Installation and operation Safety notes Safety notes Batteries Never remove parts of the CD-/DVD-ROM drive assembly Safety notes Modules with electrostatic-sensitive components Opening the server PreparationFloorstand model Removing the front cover Floorstand modelRemoving the hard disk cover PreparationRack model Rack modelRack model Loosening the screws Removing the rack front cover Removing the rack front coverPage Main memory Equipping rulesExtending/replacing the main memory Extending/replacing the main memoryMain memory Inserting a memory modulePage Accessible drives Installing an accessible 5.25-inch driveInstalling an accessible 5.25-inch drive Attaching the EasyClick rails DVD-ROM burnerAccessible drives Attaching the EasyClick rails magnetic tape drive VXA-2 Installing the hard disks extension box Installing the hard disks extension box Attaching the EasyClick railsController in the PCI slots PCIe Slot PCI SlotInstalling a controller Installing a controllerInstalling a controller Controller in the PCI slotsPCI slot assembling PCI slot assemblingRemoteView Service Board S2 LP RemoteView componentsRemoteView components RSB S2 LP RemoteView Service Board S2 LP Installing the external Scsi interface External Scsi interfacePage Conversion standard PS to hot- plug PS Taking out the standard power supply Installing the Power backplane in the PS cage Installing the PS cage Fastening the PS cage in the housing Fastening the PS cage at the rear side Inserting the power supply module Locking the power supply module Installing the dummy cover Mounting the anti-tilt bracket Fastening the anti-tilt bracket Page Converting from the floorstand model to the rack model Removing the anti-tilt bracketRight-hand side cover and the top cover build one part Removing the rubber feet Installing the operating panel module Converting from the floorstand model to the rack model Page Completion Attaching the hard disk coverAttaching the front cover Attaching the front coverClosing the server CompletionAttaching the rack front cover Attaching the plastic front coverAttaching the rack front cover Attaching the top cover Installing the server in a rack cabinet Rack model Completion Fastening the server in the rack cabinetAppendix CablingScsi version Channel Scsi version with onboard Scsi controllerScsi Cabling RAIDIDE/FD Data Cable prefix T26139 Sata version ControllerPage Abbreviations Abbreviations HDD MRL SCA Page Related publications Related Publications Index Page Comments Suggestions Corrections Page Comments Suggestions Corrections Page Information on this document Hinweise zum vorliegenden Dokument