Fujitsu TX150 S3 manual Conversion standard PS to hot- plug PS

Page 49

10Conversion standard PS to hot- plug PS

VCAUTION!

Observe the safety instructions in the chapter “Safety notes” on page 7 et seqq. .

The standard power supply can be replaced by a hot-plug power supply. The hot-plug power supply consists of up to two power supply modules. The upgrade kit contains only one power supply module (for power supply redundancy the second power supply module must be additionally ordered).

The upgrade kit for the hot-plug power supply consists of the following parts:

–PS cage with Power backplane (incl. power cables)

–locking rail

–one power supply unit

–dummy cover (if only one power supply module is installed, you have to install the dummy cover in the second bay)

–several screws

–anti-tilt bracket

VCAUTION!

After installing the hot-plug power supply the SDR (sensor data record) data base must be updated. For this sequence you need a BIOS flash diskette. This diskette contains the newest BIOS version, the BMC firmware and the SDR data.

ÊWrite a BIOS flash diskette by down loading the required data from the software pool under http://service.abg.fsc.net/support/softwareAssist.asp.

ÊOpen the server as described in the chapter “Preparation” on page 13 et seqq. .

ÊDisconnect all power cables from the system board and the drives (see the cabling plans in the Appendix).

U41604-Z156-1-76

Options Guide

41

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Primergy TX150 S3 Server System Copyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO Page Page Page Page Contents Contents Overview of the documentation IntroductionConcept and target groups Additional documentation about the serverExtensions and conversions Extensions and conversionsFurther sources of information Extension of the main memoryIntroduction Additional accessible drivesHard disks extension box Additional controllers in the PCI slotsNotational conventions Conversion standard power supply to hot-plug power supplyNotational conventions Conversion of the floorstand model to a rack modelProcedure Page Before operating the device Safety notesSafety notes Installation and operation Safety notes Safety notes Batteries Never remove parts of the CD-/DVD-ROM drive assembly Safety notes Modules with electrostatic-sensitive components Floorstand model PreparationOpening the server Floorstand model Removing the front coverPreparation Removing the hard disk coverRack model Rack modelRack model Loosening the screws Removing the rack front cover Removing the rack front coverPage Equipping rules Main memoryExtending/replacing the main memory Extending/replacing the main memoryInserting a memory module Main memoryPage Installing an accessible 5.25-inch drive Accessible drivesAttaching the EasyClick rails DVD-ROM burner Installing an accessible 5.25-inch driveAccessible drives Attaching the EasyClick rails magnetic tape drive VXA-2 Installing the hard disks extension box Attaching the EasyClick rails Installing the hard disks extension boxPCIe Slot PCI Slot Controller in the PCI slotsInstalling a controller Installing a controllerController in the PCI slots Installing a controllerPCI slot assembling PCI slot assemblingRemoteView components RemoteView Service Board S2 LPRemoteView components RSB S2 LP RemoteView Service Board S2 LP External Scsi interface Installing the external Scsi interfacePage Conversion standard PS to hot- plug PS Taking out the standard power supply Installing the Power backplane in the PS cage Installing the PS cage Fastening the PS cage in the housing Fastening the PS cage at the rear side Inserting the power supply module Locking the power supply module Installing the dummy cover Mounting the anti-tilt bracket Fastening the anti-tilt bracket Page Removing the anti-tilt bracket Converting from the floorstand model to the rack modelRight-hand side cover and the top cover build one part Removing the rubber feet Installing the operating panel module Converting from the floorstand model to the rack model Page Attaching the hard disk cover CompletionAttaching the front cover Attaching the front coverCompletion Closing the serverAttaching the plastic front cover Attaching the rack front coverAttaching the rack front cover Attaching the top cover Installing the server in a rack cabinet Fastening the server in the rack cabinet Rack model CompletionCabling AppendixScsi version Channel Scsi version with onboard Scsi controllerScsi RAID CablingIDE/FD Data Cable prefix T26139 Controller Sata versionPage Abbreviations Abbreviations HDD MRL SCA Page Related publications Related Publications Index Page Comments Suggestions Corrections Page Comments Suggestions Corrections Page Hinweise zum vorliegenden Dokument Information on this document
Top Page Image Contents