Fujitsu fi-4340C manual L1 /e, Setting double feed detection Paper Thickness

Page 69

1 Setting double feed detection (Paper Thickness)

 

Screen=! 0N1

1o / YeD o

us

b

l1 /e

2 :F

Seet od

p

When you set the use of double feed detection, you must set it as follows:

 

1. Press

or

and let the scanner disp ay Screen 1.

 

 

2.At Screen 1.

Press either the or button to set the double feed detection according to the paper thickness (transmitted light).

The paper thickness is checked using the difference between two consecutive sheets of paper fed from the ADF. On this screen, select whether or not to check for double feeding, and select the error processing.

Each time either of these buttons is pressed, the location of the blinking moves. When the button is pressed, the blinking moves from (1) to (3). When the button is pressed, the blinking moves in the opposite direction. However, if the setting by the host computer is valid, the location of the blinking does not move when either button is pressed.

(1)“No” is blinking: Paper thickness is not checked.

(2)“Yes” and “1” are blinking: Paper thickness is checked. However, a detected double feed error is displayed on the screen only; processing is continued.

(3)“Yes” and “2: Stop” are blinking: Paper thickness is checked. When the double feed error is detected, the scan processing is stopped. The error is then reported to the host.

If you want to disable the double feed, select “No” then press . Press to return.

NOTICES

1.Double Feed detection might have better results when both the paper thickness and the paper length are used.

2.When the document in ADF is not the double fed document, the previous document might be double fed, in case the scanner stops feeding by using the double feed detection.

3.Depending on the type of printing on the document, a double feed may not be detected by the paper thickness.

7-5

Image 69
Contents Fi-4340C Image Scanner Page Revisions, Disclaimers Use in Enhanced Safety Applications Bescheimigung des Herstellers / ImporteursCopying Trademarks and Registered Trademarks CopyrightFujitsu Italia S.p.A Fujitsu Group OfficesComputer Products Business Group Corporate headquarters Fujitsu Systems Business Malaysia SDN, BHDPage Preface Conventions Do not damage the power cable PrecautionsUse only the specified power cable or extension cable Wipe all dust from plug on the power supply cableDo not use the equipment if an abnormal smell is apparent Do not open the equipment without good reason Switch power OFF if the equipment is damagedDo not move the equipment alone Do not place in wet areasInsert the power plug fully into the socket Do not touch the power cable with wet handsEarth the equipment Do not block the ventilation openingsAvoid static electricity Do not leave the equipment in direct sunlight Contents Scanner Specifications Components Page Checking the Components Units and Assemblies Operator Panel ComponentsChecking the Components Powercable*2 Pad ASSY*3Units Units and AssembliesADF Part FunctionGuideAASSY Arrangement Operator PanelName of the button Function Button and LEDPage Confirm of the Manufacturing Labels Placing the scanner Installation and ConnectionsConfirm of the Manufacturing Labels Label BTurning the power switch Off Placing the scannerPlacing the Transport Lever ID No Description Setting the Scsi ID and the Scsi TerminatorMounting the Stacker Connecting the power cablePage Procedure HOW to Install the Device DriverProcedure Operating Instructions Turning the Power On Waking up the Scanner from the Low Power Mode XXXXX0XX Manual Feed Mode SettingLoading Documents on the ADF StackerForportraitmode 5mm Document Loading Documents on the Document bed Loading Documents Larger than the Document bed DocumentReading a Page from a Thick Book Clearing Paper Jams PaperADF Document Specification Document Size Precautions Paper weightDocument Quality Document typeReadsurface Country Unit Conversion ADF Document Feeder CapacityAreas not to be Perforated SideGrounding Color Areas DirectionDouble Feed Detection Condition 35mmTopofpaper Page Operator Panel Message Counter Display Operation status Temporary error AlarmCounter Function Counter DisplayOperation status No wMp t y Temporary errorFAN Al arm AlarmBoar d Activating the Setup Mode Contents of the Setup Mode Setup ModeXX0XX Activating the Setup ModeContents of the Setup Mode B/W L1 /e Setting double feed detection Paper ThicknessT1 /h Setting double feed detection Paper LengthSetting IPC pre-set mode Setting the pick start time Reset of the abrasion counterPress Next Or Previous Let the scanner display Screen Setting the time-out limitScreenV! 0=+ 17 7 IPC Status Display Screen! 1I 25 P0C-I 4PCDLow Power Mode Setting Screen 3013 Display the TPS Select InterfaceAdjust ADF Erasing Edges Select Built-In/IPC-4D Image ProcessingImage Processing Page ScreenR! 1i43 8g -h t5 = F B0 mmR i g ht Adjust FB Erasing EdgesColor to be Read in Unicolor Reading Setting the Grayscale ModeAin Reset of the Ink Remain CounterOsN Page Troubleshooting TroubleshootingTroubleshooting Consumables and Options Consumables OptionsFi-434PRIMPRINTER Fi-CMP3JPEG Compression Board Consumables Name Specification RemarksProduct name OptionsPlate Screws How to Install the Video Interface BoardAce Without IPC-4D With IPC-4D Description Option 06A6 T2/FrParameter Description L1/ L2HalftLineorPhotoArt IPC-4DIMAGE Processing Circuit Board Fi-434PRIMPRINTER TDCFi-CMP3JPEG Compression Board How to Install the fi-CMP3JPEG Compression BoardPage Scanner Specifications SCSI-2 SE Basic Product SpecificationInstallation Specification 21.9 DimensionsAbrasion counter Glossary of TermsDouble Letter Size IPC-4D Paper JAM TPS GL-6 Double IndexPaper IN-3 IN-4