Fujitsu fi-4340C manual Troubleshooting

Page 86

Troubleshooting

This chapter describes some potential problems and solutions that may occur when using this scanner. Should any of the following problems arise, refer to the relevant section listed below.

- Power doesn’t turn on	Refer to "Chapter 5-3 Cleaning & Maintenance"
- Operator Panel goes blank	Refer to "Chapter 5-4 Cleaning & Maintenance"
- Scan doesn't start	Refer to "Chapter 5-5 Cleaning & Maintenance"
- Image or photo scan output is poor	Refer to "Chapter 5-7 Cleaning & Maintenance"
- Text or line scan output is poor	Refer to "Chapter 5-8 Cleaning & Maintenance"
- Scan image is distorted or unclear	Refer to "Chapter 5-9 Cleaning & Maintenance"
- Scan image is striped	Refer to "Chapter 5-10 Cleaning & Maintenance"
- "Check" LED turns on	Refer to "Chapter 5-11 Cleaning & Maintenance"
- "Clean pick roller" LCD message	Refer to "Chapter 5-12 Cleaning & Maintenance"
- "Clean ADF glass" LCD message	Refer to "Chapter 5-19 Cleaning & Maintenance"
- Frequent double-feeds	Refer to "Chapter 5-14 Cleaning & Maintenance"
- Frequent pick-misses	Refer to "Chapter 5-16 Cleaning & Maintenance"
- Frequent paper jams	Refer to "Chapter 5-18 Cleaning & Maintenance"

NOTICE

If the problem cannot be solved, contact your sales or service representative.

●8-2

Image 86

Contents Fi-4340C Image Scanner Page Revisions, Disclaimers Copying Use in Enhanced Safety ApplicationsBescheimigung des Herstellers / Importeurs Copyright Trademarks and Registered TrademarksFujitsu Group Offices Fujitsu Italia S.p.AFujitsu Systems Business Malaysia SDN, BHD Computer Products Business Group Corporate headquartersPage Preface Conventions Use only the specified power cable or extension cable PrecautionsDo not damage the power cable Wipe all dust from plug on the power supply cableDo not use the equipment if an abnormal smell is apparent Do not move the equipment alone Switch power OFF if the equipment is damagedDo not open the equipment without good reason Do not place in wet areasEarth the equipment Do not touch the power cable with wet handsInsert the power plug fully into the socket Do not block the ventilation openingsAvoid static electricity Do not leave the equipment in direct sunlight Contents Scanner Specifications Components Page Components Checking the Components Units and Assemblies Operator PanelPowercable*2 Pad ASSY*3 Checking the ComponentsUnits and Assemblies UnitsPart Function ADFGuideAASSY Operator Panel ArrangementButton and LED Name of the button FunctionPage Installation and Connections Confirm of the Manufacturing Labels Placing the scannerLabel B Confirm of the Manufacturing LabelsPlacing the Transport Lever Turning the power switch OffPlacing the scanner Setting the Scsi ID and the Scsi Terminator ID No DescriptionConnecting the power cable Mounting the StackerPage HOW to Install the Device Driver ProcedureProcedure Operating Instructions Turning the Power On Waking up the Scanner from the Low Power Mode Manual Feed Mode Setting XXXXX0XXStacker Loading Documents on the ADFForportraitmode 5mm Document Loading Documents on the Document bed Document Loading Documents Larger than the Document bedReading a Page from a Thick Book Paper Clearing Paper JamsADF Document Specification Document Size Document Quality Paper weightPrecautions Document typeReadsurface ADF Document Feeder Capacity Country Unit ConversionSide Areas not to be PerforatedDirection Grounding Color Areas35mm Double Feed Detection ConditionTopofpaper Page Counter Display Operation status Temporary error Alarm Operator Panel MessageCounter Display Counter FunctionNo w Operation statusTemporary error Mp t yAlarm FAN Al armBoar d Setup Mode Activating the Setup Mode Contents of the Setup ModeActivating the Setup Mode XX0XXContents of the Setup Mode B/W Setting double feed detection Paper Thickness L1 /eSetting double feed detection Paper Length T1 /hSetting IPC pre-set mode Reset of the abrasion counter Setting the pick start timeSetting the time-out limit Press Next Or Previous Let the scanner display ScreenScreenV! 0=+ 17 7 Screen! 1I 25 P0C-I 4PCD IPC Status DisplayLow Power Mode Setting Select Interface Screen 3013 Display the TPSImage Processing Adjust ADF Erasing EdgesSelect Built-In/IPC-4D Image Processing Page Adjust FB Erasing Edges ScreenR! 1i43 8g -h t5 = F B0 mmR i g htSetting the Grayscale Mode Color to be Read in Unicolor ReadingReset of the Ink Remain Counter AinOsN Page Troubleshooting TroubleshootingTroubleshooting Fi-434PRIMPRINTER Fi-CMP3JPEG Compression Board Consumables and OptionsConsumables Options Name Specification Remarks ConsumablesOptions Product nameHow to Install the Video Interface Board Plate ScrewsAce 06A6 T2/Fr Without IPC-4D With IPC-4D Description OptionL1/ L2 Parameter DescriptionHalftLineorPhotoArt IPC-4DIMAGE Processing Circuit Board TDC Fi-434PRIMPRINTERHow to Install the fi-CMP3JPEG Compression Board Fi-CMP3JPEG Compression BoardPage Scanner Specifications Basic Product Specification SCSI-2 SEInstallation Specification Dimensions 21.9Glossary of Terms Abrasion counterDouble Letter Size IPC-4D Paper JAM TPS GL-6 Index DoublePaper IN-3 IN-4