Fujitsu fi-4340C manual Screen! 1I 25 P0C-I 4PCD, IPC Status Display

Page 75

5.At Screen 17,Screen 18 or Screen 19, press to increase the offset or press to decrease the

offset. Then press to activate the setting. The scanner displays the next item of the setup mode.

10 IPC Status Display

This function allows you to check whether or not the IPC-4D(IMAGE PROCESSING CIRCUIT BOARD) is installed, and whether or not fi-CMP3(JPEG COMPRESSION BOARD) is installed, and whether or not fi-434PR(IMPRINTER) is installed.

1.Press “Next” or!“Previous1I P0C-I. 4PCD

if an IPC4D(IMAGE PROCESSING CIR UIT BOARD) is installed, Screen 20 will appear.

Screen 20

if an IPC4D(IMAGE!PROCESSING10 INCIROPCUIT BOARD) is not installed,Screen 21 will appear. Screen 21

if a fi-434PR(IMPRINTER)!10only isINinstalled,OPCScreen 22OKPwillRTappear. Screen 22

if fi-434PR(IMPRINTER)! 1I 0PandCIPC4D(IMAGE-IP4CDPROCESSINGPROKTCIRCUIT BOARD) are installed, Screen 23 will appear.

Screen 23

if a fi-CMP3(JPEG!COMPRESSION10 INOPBOARD)C only isOJinstalled,KPEScreenG 24 will appear. Screen 24Check whether or not the respectively option is installed as follows.

if IPC4D(IMAGE PROCESSING CIRCUIT BOARD) and fi-CMP3(JPEG COMPRESSION BOARD) are installed,Screen 25 will appear.

Screen! 1I25 P0C-I 4PCD

JOKPEG

7-11

Image 75
Contents Fi-4340C Image Scanner Page Revisions, Disclaimers Use in Enhanced Safety Applications Bescheimigung des Herstellers / ImporteursCopying Trademarks and Registered Trademarks CopyrightFujitsu Italia S.p.A Fujitsu Group OfficesComputer Products Business Group Corporate headquarters Fujitsu Systems Business Malaysia SDN, BHDPage Preface Conventions Wipe all dust from plug on the power supply cable PrecautionsDo not damage the power cable Use only the specified power cable or extension cableDo not use the equipment if an abnormal smell is apparent Do not place in wet areas Switch power OFF if the equipment is damagedDo not open the equipment without good reason Do not move the equipment aloneDo not block the ventilation openings Do not touch the power cable with wet handsInsert the power plug fully into the socket Earth the equipmentAvoid static electricity Do not leave the equipment in direct sunlight Contents Scanner Specifications Components Page Checking the Components Units and Assemblies Operator Panel ComponentsChecking the Components Powercable*2 Pad ASSY*3Units Units and AssembliesADF Part FunctionGuideAASSY Arrangement Operator PanelName of the button Function Button and LEDPage Confirm of the Manufacturing Labels Placing the scanner Installation and ConnectionsConfirm of the Manufacturing Labels Label BTurning the power switch Off Placing the scannerPlacing the Transport Lever ID No Description Setting the Scsi ID and the Scsi TerminatorMounting the Stacker Connecting the power cablePage Procedure HOW to Install the Device DriverProcedure Operating Instructions Turning the Power On Waking up the Scanner from the Low Power Mode XXXXX0XX Manual Feed Mode SettingLoading Documents on the ADF StackerForportraitmode 5mm Document Loading Documents on the Document bed Loading Documents Larger than the Document bed DocumentReading a Page from a Thick Book Clearing Paper Jams PaperADF Document Specification Document Size Document type Paper weightPrecautions Document QualityReadsurface Country Unit Conversion ADF Document Feeder CapacityAreas not to be Perforated SideGrounding Color Areas DirectionDouble Feed Detection Condition 35mmTopofpaper Page Operator Panel Message Counter Display Operation status Temporary error AlarmCounter Function Counter DisplayOperation status No wMp t y Temporary errorFAN Al arm AlarmBoar d Activating the Setup Mode Contents of the Setup Mode Setup ModeXX0XX Activating the Setup ModeContents of the Setup Mode B/W L1 /e Setting double feed detection Paper ThicknessT1 /h Setting double feed detection Paper LengthSetting IPC pre-set mode Setting the pick start time Reset of the abrasion counterPress Next Or Previous Let the scanner display Screen Setting the time-out limitScreenV! 0=+ 17 7 IPC Status Display Screen! 1I 25 P0C-I 4PCDLow Power Mode Setting Screen 3013 Display the TPS Select InterfaceAdjust ADF Erasing Edges Select Built-In/IPC-4D Image ProcessingImage Processing Page ScreenR! 1i43 8g -h t5 = F B0 mmR i g ht Adjust FB Erasing EdgesColor to be Read in Unicolor Reading Setting the Grayscale ModeAin Reset of the Ink Remain CounterOsN Page Troubleshooting TroubleshootingTroubleshooting Consumables and Options Consumables OptionsFi-434PRIMPRINTER Fi-CMP3JPEG Compression Board Consumables Name Specification RemarksProduct name OptionsPlate Screws How to Install the Video Interface BoardAce Without IPC-4D With IPC-4D Description Option 06A6 T2/FrParameter Description L1/ L2HalftLineorPhotoArt IPC-4DIMAGE Processing Circuit Board Fi-434PRIMPRINTER TDCFi-CMP3JPEG Compression Board How to Install the fi-CMP3JPEG Compression BoardPage Scanner Specifications SCSI-2 SE Basic Product SpecificationInstallation Specification 21.9 DimensionsAbrasion counter Glossary of TermsDouble Letter Size IPC-4D Paper JAM TPS GL-6 Double IndexPaper IN-3 IN-4