Fujitsu fi-4340C manual Select Built-In/IPC-4D Image Processing, Adjust ADF Erasing Edges

Page 78

14 Select Built-In/IPC-4D Image Processing

1. Press “Next” or!16Stand letandtheIscannPeCr displayr Moddthe/ScreenI PCe31. - 4D Screen 31

2.At Screen 31, press or to select “Standard” or “IPC4D”.

When “Standard” is selected, the scanner uses its built-in image processing. On the other hand, the scanner selects the image processing of the IPC-4D(IMAGE PROCESSING CIRCUIT BOARD) when the “IPC-4D” is installed and selected.

NOTICE

The factory default is “Standard”.

NOTICE

fi-4340C has built-in Image Processing. The following image processing is supported both by the fi- 4340C and the IPC-4D(IMAGE PROCESSING CIRCUIT BOARD). As a default, the scanner built-in functions are enabled. By setting "On" using the Operator Panel, the IPC-4D image processing overrides the built-in functions.

 

Image Processing

IPC-4D

fi-4340C

 

 

 

 

1

Emphasis/Smoothing

5 x 5 matrix

3 x 3 matrix

 

 

 

 

2

Outline

Pre-threshold Laplacian

Laplacian

 

 

 

 

3

Simplified Dynamic Threshold

IPC-2 like SDTC

3 x 3 max-min

 

 

 

 

The IPC-4D(IMGGE PROCESSING CIRCUIT BOARD) support of those functions is intended for compatibility with the IPC-3/3D (except for image quality). The matrix size used in the IPC-4D(IMAGE PROCESSING CIRCUIT BOARD) is larger than the one in the fi-4340C. The fi-4340C Built-in Dynamic Threshold is a new algorithm.

15Adjust ADF Erasing Edges

1.Press “Next” or!“Previous1C7h angAandDletFethe?scannerEdNodisplaygeERS/ScreenYes32. Screen 32

7-14

Image 78
Contents Fi-4340C Image Scanner Page Revisions, Disclaimers Use in Enhanced Safety Applications Bescheimigung des Herstellers / ImporteursCopying Copyright Trademarks and Registered TrademarksFujitsu Group Offices Fujitsu Italia S.p.AFujitsu Systems Business Malaysia SDN, BHD Computer Products Business Group Corporate headquartersPage Preface Conventions Use only the specified power cable or extension cable PrecautionsDo not damage the power cable Wipe all dust from plug on the power supply cableDo not use the equipment if an abnormal smell is apparent Do not move the equipment alone Switch power OFF if the equipment is damagedDo not open the equipment without good reason Do not place in wet areasEarth the equipment Do not touch the power cable with wet handsInsert the power plug fully into the socket Do not block the ventilation openingsAvoid static electricity Do not leave the equipment in direct sunlight Contents Scanner Specifications Components Page Components Checking the Components Units and Assemblies Operator PanelPowercable*2 Pad ASSY*3 Checking the ComponentsUnits and Assemblies UnitsPart Function ADFGuideAASSY Operator Panel ArrangementButton and LED Name of the button FunctionPage Installation and Connections Confirm of the Manufacturing Labels Placing the scannerLabel B Confirm of the Manufacturing LabelsTurning the power switch Off Placing the scannerPlacing the Transport Lever Setting the Scsi ID and the Scsi Terminator ID No DescriptionConnecting the power cable Mounting the StackerPage HOW to Install the Device Driver ProcedureProcedure Operating Instructions Turning the Power On Waking up the Scanner from the Low Power Mode Manual Feed Mode Setting XXXXX0XXStacker Loading Documents on the ADFForportraitmode 5mm Document Loading Documents on the Document bed Document Loading Documents Larger than the Document bedReading a Page from a Thick Book Paper Clearing Paper JamsADF Document Specification Document Size Document Quality Paper weightPrecautions Document typeReadsurface ADF Document Feeder Capacity Country Unit ConversionSide Areas not to be PerforatedDirection Grounding Color Areas35mm Double Feed Detection ConditionTopofpaper Page Counter Display Operation status Temporary error Alarm Operator Panel MessageCounter Display Counter FunctionNo w Operation statusTemporary error Mp t yAlarm FAN Al armBoar d Setup Mode Activating the Setup Mode Contents of the Setup ModeActivating the Setup Mode XX0XXContents of the Setup Mode B/W Setting double feed detection Paper Thickness L1 /eSetting double feed detection Paper Length T1 /hSetting IPC pre-set mode Reset of the abrasion counter Setting the pick start timeSetting the time-out limit Press Next Or Previous Let the scanner display ScreenScreenV! 0=+ 17 7 Screen! 1I 25 P0C-I 4PCD IPC Status DisplayLow Power Mode Setting Select Interface Screen 3013 Display the TPSAdjust ADF Erasing Edges Select Built-In/IPC-4D Image ProcessingImage Processing Page Adjust FB Erasing Edges ScreenR! 1i43 8g -h t5 = F B0 mmR i g htSetting the Grayscale Mode Color to be Read in Unicolor ReadingReset of the Ink Remain Counter AinOsN Page Troubleshooting TroubleshootingTroubleshooting Consumables and Options Consumables OptionsFi-434PRIMPRINTER Fi-CMP3JPEG Compression Board Name Specification Remarks ConsumablesOptions Product nameHow to Install the Video Interface Board Plate ScrewsAce 06A6 T2/Fr Without IPC-4D With IPC-4D Description OptionL1/ L2 Parameter DescriptionHalftLineorPhotoArt IPC-4DIMAGE Processing Circuit Board TDC Fi-434PRIMPRINTERHow to Install the fi-CMP3JPEG Compression Board Fi-CMP3JPEG Compression BoardPage Scanner Specifications Basic Product Specification SCSI-2 SEInstallation Specification Dimensions 21.9Glossary of Terms Abrasion counterDouble Letter Size IPC-4D Paper JAM TPS GL-6 Index DoublePaper IN-3 IN-4