Fujitsu fi-4340C manual Setting IPC pre-set mode

Page 71

3 Setting IPC pre-set mode

When you set the use =!of the0NoIPC3pre-setIPmode,Cyou mustPrseteit as-follows:Set

1. Press “Next” or “Previous” and let the scanner display Screen 4. Screen 4

2. At Screen 43, press!0or3Pres-to select1 theUeprest-Settinge?andYIpressPCes/Nto activateo the pre-setting. Then the scanner displays Screen 5.

Screen 5

NOTICES

The following IPC pre-settings can be selected when IPC-4D is installed:

Preset 1: Captures texts printed on the colored background

Preset 2: Produces an image with good contrast

Preset 3: OCR Smoothing

Preset 4: Image Smoothing

Preset 5: Dither

Preset 9:Pre-printed paper (color) orientation

Preset 10:No-carbon paper orientation

The following built-in IPC pre-settings can be selected even though IPC-4D is not installed:

Sharpen

Darken Character

Copy Quality

3.At Screen 5, select “Yes” or “No”. Note that when you select “Yes”, the IPC setting from the Host computer is ignored. If you select “No”, the IPC setting will be changed according to the host setting.

Finally press .

NOTICE

When you select the Copy Quality, select the scanner and printer settings carefully to get the best quality.

7-7

Image 71
Contents Fi-4340C Image Scanner Page Revisions, Disclaimers Copying Use in Enhanced Safety ApplicationsBescheimigung des Herstellers / Importeurs Trademarks and Registered Trademarks CopyrightFujitsu Italia S.p.A Fujitsu Group OfficesComputer Products Business Group Corporate headquarters Fujitsu Systems Business Malaysia SDN, BHDPage Preface Conventions Wipe all dust from plug on the power supply cable PrecautionsDo not damage the power cable Use only the specified power cable or extension cableDo not use the equipment if an abnormal smell is apparent Do not place in wet areas Switch power OFF if the equipment is damagedDo not open the equipment without good reason Do not move the equipment aloneDo not block the ventilation openings Do not touch the power cable with wet handsInsert the power plug fully into the socket Earth the equipmentAvoid static electricity Do not leave the equipment in direct sunlight Contents Scanner Specifications Components Page Checking the Components Units and Assemblies Operator Panel ComponentsChecking the Components Powercable*2 Pad ASSY*3Units Units and AssembliesADF Part FunctionGuideAASSY Arrangement Operator PanelName of the button Function Button and LEDPage Confirm of the Manufacturing Labels Placing the scanner Installation and ConnectionsConfirm of the Manufacturing Labels Label BPlacing the Transport Lever Turning the power switch OffPlacing the scanner ID No Description Setting the Scsi ID and the Scsi TerminatorMounting the Stacker Connecting the power cablePage Procedure HOW to Install the Device DriverProcedure Operating Instructions Turning the Power On Waking up the Scanner from the Low Power Mode XXXXX0XX Manual Feed Mode SettingLoading Documents on the ADF StackerForportraitmode 5mm Document Loading Documents on the Document bed Loading Documents Larger than the Document bed DocumentReading a Page from a Thick Book Clearing Paper Jams PaperADF Document Specification Document Size Document type Paper weightPrecautions Document QualityReadsurface Country Unit Conversion ADF Document Feeder CapacityAreas not to be Perforated SideGrounding Color Areas DirectionDouble Feed Detection Condition 35mmTopofpaper Page Operator Panel Message Counter Display Operation status Temporary error AlarmCounter Function Counter DisplayOperation status No wMp t y Temporary errorFAN Al arm AlarmBoar d Activating the Setup Mode Contents of the Setup Mode Setup ModeXX0XX Activating the Setup ModeContents of the Setup Mode B/W L1 /e Setting double feed detection Paper ThicknessT1 /h Setting double feed detection Paper LengthSetting IPC pre-set mode Setting the pick start time Reset of the abrasion counterPress Next Or Previous Let the scanner display Screen Setting the time-out limitScreenV! 0=+ 17 7 IPC Status Display Screen! 1I 25 P0C-I 4PCDLow Power Mode Setting Screen 3013 Display the TPS Select InterfaceImage Processing Adjust ADF Erasing EdgesSelect Built-In/IPC-4D Image Processing Page ScreenR! 1i43 8g -h t5 = F B0 mmR i g ht Adjust FB Erasing EdgesColor to be Read in Unicolor Reading Setting the Grayscale ModeAin Reset of the Ink Remain CounterOsN Page Troubleshooting TroubleshootingTroubleshooting Fi-434PRIMPRINTER Fi-CMP3JPEG Compression Board Consumables and OptionsConsumables Options Consumables Name Specification RemarksProduct name OptionsPlate Screws How to Install the Video Interface BoardAce Without IPC-4D With IPC-4D Description Option 06A6 T2/FrParameter Description L1/ L2HalftLineorPhotoArt IPC-4DIMAGE Processing Circuit Board Fi-434PRIMPRINTER TDCFi-CMP3JPEG Compression Board How to Install the fi-CMP3JPEG Compression BoardPage Scanner Specifications SCSI-2 SE Basic Product SpecificationInstallation Specification 21.9 DimensionsAbrasion counter Glossary of TermsDouble Letter Size IPC-4D Paper JAM TPS GL-6 Double IndexPaper IN-3 IN-4