Cisco Systems N6004SBUNP1L, N6KC600496Q, N6001SBUNP1, N6000, N6KC600164P manual Statement

Page 31

Chapter 2 Installing the Cisco Nexus 6000 Series Switches

Starting the Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .

Note Do not connect the Ethernet port to the LAN until the initial switch configuration has been performed. For instructions on configuring the switch, see the Cisco Nexus 6000 Series CLI Configuration Guide. For instructions on connecting to the console port, see the “Connecting to the Console Port” section on page 3-2.

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046

To power up the switch and verify hardware operation, follow these steps:

Step 1 Verify that empty power supply slots have filler panels installed, the faceplates of all modules are flush with the front of the chassis, and the captive screws of the power supplies, fan module, and all expansion modules are tight.

Step 2 Verify that the power supply and the fan modules are installed.

Note Depending on the outlet receptacle on your power distribution unit, you may need the optional jumper power cord to connect the switch to your outlet receptacle. See the “Jumper Power Cord” section on page C-8.

Step 3 Ensure that the switch is adequately grounded as described in the “Grounding the Switch” section on page 2-7, and that the power cables are connected to outlets that have the required AC power voltages (see the “Power Specifications” section on page B-2).

Step 4 For the switch, insert each end of the power clip (from the accessory kit) into holes on tabs located on either side of the power connectors (see Figure 2-16).

Step 5 Connect each power cable to the power connectors on the chassis and an AC power source. Press the power cable into the power clip to endure that the power cable stays connected to the chassis when bumped. The switch should power on as soon as you connect the power cable.

Step 6 Listen for the fans; they should begin operating when the power cable is plugged in.

Step 7 After the switch boots, verify that the LED operation is as follows:

•Fan module—Status LED is green.

•Power supply—Status LED is green.

•After initialization, the system status LED is green, indicating that all chassis environmental monitors are reporting that the system is operational. If this LED is orange or red, then one or more environmental monitor is reporting a problem.

•The Link LEDs for the Ethernet connector should not be on unless the cable is connected.

Note The link LEDs for the Fibre Channel ports remain yellow until the ports are enabled, and the LED for the Ethernet connector port remains off until the port is connected.

Step 8 Try removing and reinstalling a component that is not operating correctly. If it still does not operate correctly, contact your customer service representative for a replacement.

 

 

Cisco Nexus 6000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

2-13

 

 

 

 

 

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Americas Headquarters Cisco Nexus 6000 Series Hardware Installation GuidePage Chapter and Title Description PrefaceAudience OrganizationBewaar Deze Instructies ConventionsAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar GEM Disse Anvisninger Viii Preface Related Documentation Obtaining Documentation and Submitting a Service RequestFeatures Cisco Nexus 6004 SwitchOverview Chassis Front View of the Cisco Nexus 6004 switchExpansion Modules Rear View of the Cisco Nexus 6004 SwitchCisco Nexus 6004 Expansion Module PortsPart Number Power Supply Power SupplyFan Module Airflow Cisco SFP Description TransceiversOverview Cisco Nexus 6004 Switch Installing the Cisco Nexus 6000 Series Switches Installation Guidelines Preparing for InstallationInstallation Options with Racks and Cabinets Chassis WeightPage Required Equipment Unpacking and Inspecting the SwitchInstalling a Cisco Nexus 6004 switch Installing the SwitchQuantity Part Description Cisco Nexus 6000 Series Hardware Installation Guide Grounding the Switch Environment Severity Level Grounding Recommendations Proper Grounding PracticesPreventing Electrostatic Discharge Damage OL-15902-01 Required Tools and Equipment Establishing the System GroundGrounding the Cisco Nexus 6000 Series Chassis Starting the Switch Statement Cisco Nexus 6000 Series Hardware Installation Guide Connecting the Switch Preparing for Network Connections Connecting to the Console PortInstalling a Transceiver Connecting to the Ethernet Connector PortConnecting to an Ethernet Port Installing and Replacing TransceiversReplacing a Transceiver Installing a Cable into an Transceiver Installing Cables into TransceiversReplacing a Cable for a Transceiver Connecting the Switch Connecting to an Ethernet Port Replacing Expansion Modules Replacing ComponentsRemoving a LEM Replacing LEMsRemoving a Module Installing a LEMInstalling a Module Replacing ModulesRemoving a Power Supply Replacing or Installing Power SuppliesInstalling a Power Supply Wiring a DC Power Connector Wiring the DC Power Connector Replacing a Fan Module Installing a Fan ModuleRemoving a Fan Module Removing the Cisco Nexus 6000 Platform Chassis Cabinet and Rack Requirements Cabinet and Rack InstallationGeneral Requirements for Cabinets and Racks Requirements Specific to Perforated Cabinets Cable Management GuidelinesDescription Specification Technical SpecificationsSwitch Specifications Environmental SpecificationsProperty Cisco Nexus 6004Switch Expansion Module SpecificationsPower Specifications Specifications for the Cisco Nexus 6004 Power SupplyAppendix B Technical Specifications Appendix B Technical Specifications Cable RJ-45 Connector Pinouts Cable and Port SpecificationsSignal Name P1, P1-45 Pins P2, DB-9 Pins Description Feet Meters Illustration Supported Power Cords and PlugsConsole Port LengthCAB-N5K6A-NA CAB-9K10A-AU Plug CAB-9K10A-SW CAB-C13-CBN Figure C-14 Jumper Power CordLEDs Indicator Location Function Color Status StateChassis and Module LED Descriptions Power Supply Condition Green Amber Conditions Indicated by the Power Supply LEDsPort LEDs Link State LED State Ethernet Port LEDsEthernet and Fibre Channel LEDs Status DescriptionAppendix D LEDs Port LEDs Switch Hardware Best Practices Troubleshooting Hardware ComponentsOverview Power Supply Condition Power LED Status Fail LED Status Power Supply ConditionsInstallation Best Practices Switch Operation Best PracticesPage Cisco Nexus 6000 Series Hardware Installation Guide Cisco Nexus 6004 Switch Accessory Kit Accessory KitsOL-15902-02-xx Site Preparation Checklist Site Planning and Maintenance RecordsTask No Planning Activity Verified By Time Date Contact and Site Information Slot Module Type Module Serial Number Supervisor Chassis and Module Information
Related manuals
Manual 204 pages 40.67 Kb
Top Page Image Contents