Cisco Systems N6004SBUNP1L, N6KC600496Q, N6001SBUNP1, N6000, N6KC600164P Wiring a DC Power Connector

Page 43

Chapter 4 Replacing Components

Replacing or Installing Power Supplies

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .

Step 1 Ensure that the system (earth) ground connection has been made. For ground connection instructions, see the “Grounding the Switch” section on page 2-7.

Step 2 If the power supply bay has a filler panel, press the latches on the sides of the filler panel, and then slide it out of the power supply bay.

Step 3 Hold the power supply by the handle and position it so that the release latch is on the right, and then slide it into the power supply bay, ensuring that the power supply is fully seated in the bay.

Step 4 Plug the AC power cable or DC wiring connector into the inlet receptacle at the rear of the chassis. For a DC installation, you should secure the plug to the power supply by tightening both captive screws on the plug.

Note Depending on the outlet receptacle on your power distribution unit, you may need the optional jumper power cord to connect the Cisco Nexus 6004 switch to your outlet receptacle. See the “Jumper Power Cord” section on page C-8.

Step 5 Connect the other end of the power cable to an AC power source. DC sources should connect negative (black wire) and then positive (red wire) connections.

Caution In a system with dual power supplies, connect each power supply to a separate power source. In case of a power source failure, the second source will most likely still be available.

Step 6 Verify the power supply operation by checking that the power supply LED is green.

Wiring a DC Power Connector

Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning Hazardous voltage or energy may be present on DC power terminals. Always replace cover when terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in place. Statement 1075

Cisco Nexus 6000 Series Hardware Installation Guide

 

OL-15902-01

4-5

 

 

 

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Americas Headquarters Cisco Nexus 6000 Series Hardware Installation GuidePage Chapter and Title Description PrefaceAudience OrganizationBewaar Deze Instructies ConventionsAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar GEM Disse Anvisninger Viii Preface Related Documentation Obtaining Documentation and Submitting a Service RequestFeatures Cisco Nexus 6004 SwitchOverview Chassis Front View of the Cisco Nexus 6004 switchExpansion Modules Rear View of the Cisco Nexus 6004 SwitchCisco Nexus 6004 Expansion Module PortsPart Number Power Supply Power SupplyFan Module Airflow Cisco SFP Description TransceiversOverview Cisco Nexus 6004 Switch Installing the Cisco Nexus 6000 Series Switches Installation Guidelines Preparing for InstallationInstallation Options with Racks and Cabinets Chassis WeightPage Required Equipment Unpacking and Inspecting the SwitchInstalling a Cisco Nexus 6004 switch Installing the SwitchQuantity Part Description Cisco Nexus 6000 Series Hardware Installation Guide Grounding the Switch Environment Severity Level Grounding Recommendations Proper Grounding PracticesPreventing Electrostatic Discharge Damage OL-15902-01 Required Tools and Equipment Establishing the System GroundGrounding the Cisco Nexus 6000 Series Chassis Starting the Switch Statement Cisco Nexus 6000 Series Hardware Installation Guide Connecting the Switch Preparing for Network Connections Connecting to the Console PortInstalling a Transceiver Connecting to the Ethernet Connector PortConnecting to an Ethernet Port Installing and Replacing TransceiversReplacing a Transceiver Installing a Cable into an Transceiver Installing Cables into TransceiversReplacing a Cable for a Transceiver Connecting the Switch Connecting to an Ethernet Port Replacing Expansion Modules Replacing ComponentsRemoving a LEM Replacing LEMsRemoving a Module Installing a LEMInstalling a Module Replacing ModulesRemoving a Power Supply Replacing or Installing Power SuppliesInstalling a Power Supply Wiring a DC Power Connector Wiring the DC Power Connector Replacing a Fan Module Installing a Fan ModuleRemoving a Fan Module Removing the Cisco Nexus 6000 Platform Chassis Cabinet and Rack Requirements Cabinet and Rack InstallationGeneral Requirements for Cabinets and Racks Requirements Specific to Perforated Cabinets Cable Management GuidelinesDescription Specification Technical SpecificationsSwitch Specifications Environmental SpecificationsProperty Cisco Nexus 6004Switch Expansion Module SpecificationsPower Specifications Specifications for the Cisco Nexus 6004 Power SupplyAppendix B Technical Specifications Appendix B Technical Specifications Cable RJ-45 Connector Pinouts Cable and Port SpecificationsSignal Name P1, P1-45 Pins P2, DB-9 Pins Description Feet Meters Illustration Supported Power Cords and PlugsConsole Port LengthCAB-N5K6A-NA CAB-9K10A-AU Plug CAB-9K10A-SW CAB-C13-CBN Figure C-14 Jumper Power CordLEDs Indicator Location Function Color Status StateChassis and Module LED Descriptions Power Supply Condition Green Amber Conditions Indicated by the Power Supply LEDsPort LEDs Link State LED State Ethernet Port LEDsEthernet and Fibre Channel LEDs Status DescriptionAppendix D LEDs Port LEDs Switch Hardware Best Practices Troubleshooting Hardware ComponentsOverview Power Supply Condition Power LED Status Fail LED Status Power Supply ConditionsInstallation Best Practices Switch Operation Best PracticesPage Cisco Nexus 6000 Series Hardware Installation Guide Cisco Nexus 6004 Switch Accessory Kit Accessory KitsOL-15902-02-xx Site Preparation Checklist Site Planning and Maintenance RecordsTask No Planning Activity Verified By Time Date Contact and Site Information Slot Module Type Module Serial Number Supervisor Chassis and Module Information
Related manuals
Manual 204 pages 40.67 Kb
Top Page Image Contents