Cisco Systems N6001SBUNP1, N6004SBUNP1L manual Replacing Components, Replacing Expansion Modules

Page 39

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .

C H A P T E R 4

Replacing Components

This chapter describes how to remove and install components for the Cisco Nexus 6000 Platform switch. This section includes the following sections:

•Replacing Expansion Modules, page 4-1

•Replacing LEMs, page 4-2

•Replacing Modules, page 4-3

•Replacing or Installing Power Supplies, page 4-4

•Replacing a Fan Module, page 4-7

•Removing the Cisco Nexus 6000 Platform Chassis, page 4-8

Replacing Expansion Modules

Caution To prevent ESD damage, wear grounding wrist straps during these procedures and handle expansion modules by the carrier edges only.

Install the switch in the rack before installing expansion modules. For information about installing the chassis, see the “Installing the Switch” section on page 2-5.

This section includes the following topics:

•Removing an Expansion Module from a Cisco Nexus 6000 Platform Chassis, page 4-1

•Installing an Expansion Module in a Cisco Nexus 6000 Platform Chassis, page 4-2

Removing an Expansion Module from a Cisco Nexus 6000 Platform Chassis

 

 

To remove an expansion module from the Cisco Nexus 6000 Platform switch chassis, follow these steps:

 

 

 

 

Step 1

Disconnect any network interface cables attached to the module.

 

Step 2

Open the packing materials for the module and prepare an antistatic surface for uninstalled modules.

 

Step 3

Loosen the captive screw on the ejector lever so that the lever can move.

 

Step 4

Rotate the ejector lever fully from the front of the module until it stops at about 80 degrees from the front.

 

 

Cisco Nexus 6000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-15902-01

 

 

4-1

 

 

 

 

 

Page 38 Page 40
Image 39
Page 38 Page 40
Contents
Americas Headquarters Cisco Nexus 6000 Series Hardware Installation GuidePage Chapter and Title Description PrefaceAudience OrganizationBewaar Deze Instructies ConventionsWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar GEM Disse Anvisninger Viii Preface Related Documentation Obtaining Documentation and Submitting a Service RequestCisco Nexus 6004 Switch FeaturesOverview Chassis Front View of the Cisco Nexus 6004 switchExpansion Modules Rear View of the Cisco Nexus 6004 SwitchCisco Nexus 6004 Expansion Module PortsPower Supply Part Number Power SupplyFan Module Airflow Cisco SFP Description TransceiversOverview Cisco Nexus 6004 Switch Installing the Cisco Nexus 6000 Series Switches Installation Guidelines Preparing for InstallationInstallation Options with Racks and Cabinets Chassis WeightPage Required Equipment Unpacking and Inspecting the SwitchInstalling the Switch Installing a Cisco Nexus 6004 switchQuantity Part Description Cisco Nexus 6000 Series Hardware Installation Guide Grounding the Switch Environment Severity Level Grounding Recommendations Proper Grounding PracticesPreventing Electrostatic Discharge Damage OL-15902-01 Establishing the System Ground Required Tools and EquipmentGrounding the Cisco Nexus 6000 Series Chassis Starting the Switch Statement Cisco Nexus 6000 Series Hardware Installation Guide Connecting the Switch Preparing for Network Connections Connecting to the Console Port Installing a Transceiver Connecting to the Ethernet Connector Port Connecting to an Ethernet Port Installing and Replacing TransceiversReplacing a Transceiver Installing Cables into Transceivers Installing a Cable into an TransceiverReplacing a Cable for a Transceiver Connecting the Switch Connecting to an Ethernet Port Replacing Expansion Modules Replacing ComponentsRemoving a LEM Replacing LEMsRemoving a Module Installing a LEMInstalling a Module Replacing ModulesReplacing or Installing Power Supplies Removing a Power SupplyInstalling a Power Supply Wiring a DC Power Connector Wiring the DC Power Connector Installing a Fan Module Replacing a Fan ModuleRemoving a Fan Module Removing the Cisco Nexus 6000 Platform Chassis Cabinet and Rack Installation Cabinet and Rack RequirementsGeneral Requirements for Cabinets and Racks Requirements Specific to Perforated Cabinets Cable Management GuidelinesDescription Specification Technical SpecificationsSwitch Specifications Environmental SpecificationsProperty Cisco Nexus 6004Switch Expansion Module SpecificationsPower Specifications Specifications for the Cisco Nexus 6004 Power SupplyAppendix B Technical Specifications Appendix B Technical Specifications Cable and Port Specifications Cable RJ-45 Connector PinoutsSignal Name P1, P1-45 Pins P2, DB-9 Pins Description Feet Meters Illustration Supported Power Cords and PlugsConsole Port LengthCAB-N5K6A-NA CAB-9K10A-AU Plug CAB-9K10A-SW CAB-C13-CBN Figure C-14 Jumper Power CordIndicator Location Function Color Status State LEDsChassis and Module LED Descriptions Conditions Indicated by the Power Supply LEDs Power Supply Condition Green AmberPort LEDs Link State LED State Ethernet Port LEDsEthernet and Fibre Channel LEDs Status DescriptionAppendix D LEDs Port LEDs Troubleshooting Hardware Components Switch Hardware Best PracticesOverview Power Supply Condition Power LED Status Fail LED Status Power Supply ConditionsInstallation Best Practices Switch Operation Best PracticesPage Cisco Nexus 6000 Series Hardware Installation Guide Cisco Nexus 6004 Switch Accessory Kit Accessory KitsOL-15902-02-xx Site Preparation Checklist Site Planning and Maintenance RecordsTask No Planning Activity Verified By Time Date Contact and Site Information Slot Module Type Module Serial Number Supervisor Chassis and Module Information
Related manuals
Manual 204 pages 40.67 Kb
Top Page Image Contents