Cisco Systems 6000 manual Verifying the Installation

Page 15

Verifying the Installation

Figure 6 Ejector Levers and Captive Installation Screws

WS-X6K-SUP1

STATUS SYSTEMACTIVE MGMT

PWR RESET

SUPERVISOR I

	Switch	Load
CONSOLE	100%
CONSOLE
PORT
MODE
CONSOLE	1%	PCMCIA	EJECT
	1%

PORT 1

LINK

PORT 2

LINK

16059

Ejector lever	Captive
	installation
	screws

Step 9 Using the thumb and forefinger of each hand, simultaneously push in the left and right levers to fully seat the CSM in the backplane connector.

Caution Always use the ejector levers when installing or removing the CSM. A module that is partially seated in the backplane will cause the system to halt and subsequently crash.

Note If you perform a hot swap, the console displays the message “Module n has been inserted.” This message does not appear, however, if you are connected to the Catalyst 6000 family switch through a Telnet session.

Step 10 Use a screwdriver to tighten the captive installation screws on the left and right ends of the CSM.

This completes the CSM installation procedure.

Verifying the Installation

When you install the CSM into the Catalyst 6000 family switch, the module goes through a boot sequence that requires no intervention. At the successful conclusion of the boot sequence, the green status LED will illuminate and remain on.

		Catalyst 6000 Family Content Switching Module Installation and Configuration Note

	78-11631-02 Rev. A0			15
	78-11631-02 Rev. A0			15

Image 15

Contents Contents Overview Features Describes the features of the CSMThese sections describe the CSM CSM front panel features are shown in Figure Front Panel DescriptionStatus LED Operation Mode RJ-45 ConnectorOff Red Orange Green Green to Orange Content Switching Module and Servers Client-to-CSM-to-Server Traffic Flow Client-to-Content Switching Module-to-Server Traffic FlowSafety Overview CSM memory is not configurable System RequirementsMemory Requirements 72-876-01 Console Cable Not applicable Power RequirementsHardware Supported Environmental RequirementsSoftware Requirements Installing the Content Switching ModulePreparing to Install the CSM Required ToolsInstalling the CSM Power supply Installing Modules in the Catalyst 6000 Family Switch Verifying the Installation Verifying the InstallationUsing the Command-Line Interface Accessing Online HelpUpgrading to a New Software Release Routerconfig# power cycle module slot-number Upgrading from the Supervisor Engine BootflashSet up a session between the supervisor engine and the CSM CSM upgrade 127.0.0.zz c6slb-apc.revision-num.binUpgrading from a Pcmcia Card Routerconfig# tftp-server slotxc6slb-apc.revision-num.binCSM upgrade slot0 c6slb-apc.revision-num.bin Router config# power cycle module slot-numberRouter# vlan database Configuring the Content Switching ModuleSwitchport Switchport access vlanConfiguration Overview Configure the required parameters in the following sections Configuring VLANsSee for the following notes Configuring VLANsConfiguring Server-Side VLANs Configuring Client-Side VLANsConfiguring Server Farms Configuring Real Servers Configuring Policies Configuring Maps Configure multiple cookies Configure multiple cookies into a cookie mapConfiguring Sticky Groups Configuring Virtual Servers Configuring Dynamic Feedback Protocol Configuring TCP ParametersConfiguring Redirect Virtual Servers Configuring Client NAT Pools Configuring Server NAT Writing and Restoring ConfigurationsSingle Subnet Bridge Mode Configuration Configuration ExamplesExit to have the configuration take effect Enter the Vlan modeConfigure a client-side Vlan Configure a server-side VlanSecure Router Mode Configuration Vlan modeCreate the client-side Vlan 2 and enter the SLB Exit the submode Fault-Tolerant ConfigurationRouterconfig# ip slb vlan 3 server Create the server-side Vlan 3 and enter the SLBRouterconfig-if#service-policy input Venus Router# configure terminalRouterconfig# mac access-list extended Venus Routerconfig# int GigabitEthernet 2/1Configuration Parameter On Both Content Switching Modules Fault-tolerant configuration, the following rules apply192.158.38.10 Create the client-side Vlan 2 and enter the SLB Vlan modeAssign the Content Switching IP address on Router B Hsrp addressConfigure a client-side VLAN2 Assign the default route for VlanDefine Vlan 9 as a fault-tolerant Vlan Create the Content Switching primaryHsrp Configuration Overview Configuring HsrpCSG Vlan Configure Switch 2-FT2 Hsrp secondary as followsConfigure VLANs on Hsrp FT2 as follows Configuring CSM VLANsConfiguring Probes for Health Monitoring Configure EtherChannel on both switches as followsAdd ports to the EtherChannel as follows Telnet creates a Telnet probe with a default configuration Probe-name is the name of the probe being configured it hasHttp creates an Http probe with a default configuration Icmp creates an Icmp probe with a default configurationHttp Probe Commands Available to all Probe ConfigurationsIcmp Probe TCP Probe FTP, SMTP, and Telnet ProbeDNS Probe Submode Configuring Route Health Injection Understanding RHIRHI Overview Routing to VIP Addresses With RHI Routing to VIP Addresses Without RHIUnderstanding Propagation of VIP Availability Information Configuring RHI for Virtual ServersRouterconfig# ip slb vserver vserver1 Understanding How the CSM Determines VIP AvailabilityTranslated Safety Warnings Safety Information Referral WarningRegulatory Standards Compliance Wrist Strap Warning Blank Faceplate Installation Requirement Warning Translated Safety Warnings Related Documentation Qualified Personnel WarningRelease Notes for Catalyst 6000 Family IOS Software Ordering Documentation Obtaining DocumentationWorld Wide Web Documentation CD-ROMCisco.com Contacting TAC by Using the Cisco TAC WebsiteTo access Cisco.com, go to the following website Obtaining Technical AssistanceContacting TAC by Telephone Obtaining Technical Assistance