Cisco Systems 6000 manual See for the following notes, Configuring VLANs

Page 22

Configuring the Content Switching Module

Figure 8 Configuring VLANs

Client-side VLAN IP address

*

NAS

HSRP

Catalyst 6500

Content

Services

Gateway

Server-side VLAN

Content provider

Gateway

**

PDA

handset

See Figure 8 for the following notes:

55703

Note *Any router configured as a client-side gateway or a next hop router for servers more than one hop away must have ICMP redirects disabled. The CSM does not perform a Layer 3 lookup to forward traffic; the CSM cannot act upon ICMP redirects.

Note ** HSRP provides automatic router backup using an active standby router that allows active and standby routers in an HSRP group to exchange messages and respond to topology changes by selecting a new active router dynamically. Because traffic can come from both the virtual and physical MAC addresses of the gateway, the CSM uses two entries per virtual IP gateway configured. You can configure only seven client gateways on the CSM. An HSRP group is assigned one client gateway for the virtual IP address when it is configured. (See the “Configuring HSRP” section on page 43.)

	Catalyst 6000 Family Content Switching Module Installation and Configuration Note
22	78-11631-02 Rev. A0

Image 22

Contents Contents Overview Describes the features of the CSM FeaturesThese sections describe the CSM Front Panel Description CSM front panel features are shown in FigureStatus LED RJ-45 Connector Operation ModeOff Red Orange Green Green to Orange Content Switching Module and Servers Client-to-Content Switching Module-to-Server Traffic Flow Client-to-CSM-to-Server Traffic FlowSafety Overview System Requirements CSM memory is not configurableMemory Requirements Environmental Requirements Power RequirementsHardware Supported 72-876-01 Console Cable Not applicableRequired Tools Installing the Content Switching ModulePreparing to Install the CSM Software RequirementsInstalling the CSM Power supply Installing Modules in the Catalyst 6000 Family Switch Verifying the Installation Verifying the InstallationAccessing Online Help Using the Command-Line InterfaceUpgrading to a New Software Release CSM upgrade 127.0.0.zz c6slb-apc.revision-num.bin Upgrading from the Supervisor Engine BootflashSet up a session between the supervisor engine and the CSM Routerconfig# power cycle module slot-numberRouter config# power cycle module slot-number Routerconfig# tftp-server slotxc6slb-apc.revision-num.binCSM upgrade slot0 c6slb-apc.revision-num.bin Upgrading from a Pcmcia CardSwitchport access vlan Configuring the Content Switching ModuleSwitchport Router# vlan databaseConfiguration Overview Configuring VLANs Configure the required parameters in the following sectionsConfiguring VLANs See for the following notesConfiguring Client-Side VLANs Configuring Server-Side VLANsConfiguring Server Farms Configuring Real Servers Configuring Policies Configuring Maps Configure multiple cookies into a cookie map Configure multiple cookiesConfiguring Sticky Groups Configuring Virtual Servers Configuring TCP Parameters Configuring Dynamic Feedback ProtocolConfiguring Redirect Virtual Servers Configuring Client NAT Pools Writing and Restoring Configurations Configuring Server NATConfiguration Examples Single Subnet Bridge Mode ConfigurationConfigure a server-side Vlan Enter the Vlan modeConfigure a client-side Vlan Exit to have the configuration take effectVlan mode Secure Router Mode ConfigurationCreate the client-side Vlan 2 and enter the SLB Create the server-side Vlan 3 and enter the SLB Fault-Tolerant ConfigurationRouterconfig# ip slb vlan 3 server Exit the submodeRouterconfig# int GigabitEthernet 2/1 Router# configure terminalRouterconfig# mac access-list extended Venus Routerconfig-if#service-policy input VenusFault-tolerant configuration, the following rules apply Configuration Parameter On Both Content Switching ModulesRouter B Hsrp address Create the client-side Vlan 2 and enter the SLB Vlan modeAssign the Content Switching IP address on 192.158.38.10Create the Content Switching primary Assign the default route for VlanDefine Vlan 9 as a fault-tolerant Vlan Configure a client-side VLAN2Configuring Hsrp Hsrp Configuration OverviewConfigure Switch 2-FT2 Hsrp secondary as follows CSG VlanConfiguring CSM VLANs Configure VLANs on Hsrp FT2 as followsConfigure EtherChannel on both switches as follows Configuring Probes for Health MonitoringAdd ports to the EtherChannel as follows Icmp creates an Icmp probe with a default configuration Probe-name is the name of the probe being configured it hasHttp creates an Http probe with a default configuration Telnet creates a Telnet probe with a default configurationCommands Available to all Probe Configurations Http ProbeIcmp Probe FTP, SMTP, and Telnet Probe TCP ProbeDNS Probe Submode Understanding RHI Configuring Route Health InjectionRHI Overview Routing to VIP Addresses Without RHI Routing to VIP Addresses With RHIUnderstanding How the CSM Determines VIP Availability Configuring RHI for Virtual ServersRouterconfig# ip slb vserver vserver1 Understanding Propagation of VIP Availability InformationSafety Information Referral Warning Translated Safety WarningsRegulatory Standards Compliance Wrist Strap Warning Blank Faceplate Installation Requirement Warning Translated Safety Warnings Qualified Personnel Warning Related DocumentationRelease Notes for Catalyst 6000 Family IOS Software Documentation CD-ROM Obtaining DocumentationWorld Wide Web Ordering DocumentationObtaining Technical Assistance Contacting TAC by Using the Cisco TAC WebsiteTo access Cisco.com, go to the following website Cisco.comContacting TAC by Telephone Obtaining Technical Assistance